# OBD-II P2135: OBD-II P2135: Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation

> **Quick Answer:** Code **P2135** (SAE J2012) means the dual internal **Throttle Position Sensors (`TPS "A" / "B"`)** mounted on the **drive-by-wire Electronic Throttle Body (`ETB`)** disagreed beyond safety limits—for example, `TPS1` rising `~0.5->4.5 V` vs `TPS2` falling `~4.5->0.5 V` on a shared `5.0 V` reference—forcing **immediate Reduced Engine Power / Limp Mode** (`~1,200–2,000 RPM` cap). **Check battery & charging health (`P0562`) FIRST**, because weak `5 V` voltage during cranking trips false `P2135`. Next, inspect the **6-pin throttle body connector pigtail** for terminal fretting or moisture corrosion, check for a **carbon-binding throttle plate**, and if `TPS1/TPS2` tracks diverge during a slow KOEO sweep, replace the **Electronic Throttle Body (or pigtail)** and perform an **Idle Air Volume / Throttle Relearn** ($15–$260 DIY; $220–$640 shop).

- **URL:** https://faultcodes.org/automotive/obd2-p2135
- **Category:** Automotive & OBD-II
- **Brand / Standard:** OBD-II
- **System Area:** Powertrain & Engine Management
- **Severity:** Critical — Stop Immediately
- **Safe to Operate?:** No — Risk of Damage
- **DIY Difficulty:** Moderate (Intermediate)
- **Updated:** 2026-11-22T00:00:00Z

## What This Fault Code Means
Because electronic drive-by-wire systems have no steel accelerator cable, the ECM demands redundant opposite-slope feedback (`TPS1 + TPS2 ≈ 5.0 V`) inside the throttle housing to verify exact throttle blade angle. Even a brief `> 0.25–0.50 V` mismatch from dirty potentiometer tracks, fretted connector pins, or sticky carbon holding the blade against motor commands triggers `P2135` and locks out normal throttle response for safety.

## Technical Thresholds & Specifications
| Parameter / Condition | Factory Spec / Threshold | Note |
| --- | --- | --- |
| Dual TPS Correlation Logic | TPS1 ~0.5->4.5 V vs TPS2 ~4.5->0.5 V (sum ~5.0 V) | Inverse dual-track redundancy on 5.0 V ref; > ~0.25–0.5 V mismatch sets P2135 |
| Failsafe Vehicle Response | Immediate Reduced Engine Power / Limp Mode | Prevents unintended acceleration when redundant blade position feedback disagrees |
| Mandatory Post-Repair Step | Throttle Body / Idle Air Volume Relearn | Required after cleaning or ETB swap so ECM learns closed-stop offset |
| Primary Non-ETB Suspects | Low battery (P0562) & fretted 6-pin ETB pigtail | Always check before spending money on a full Electronic Throttle Body |

## Commonly Affected Models & Service Bulletins
- Chevrolet / GMC Silverado, Tahoe, Equinox, Malibu & Trailblazer (6-pin ETB pigtail & throttle body)
- Chrysler / Dodge / Jeep / Ram Hemi & Pentastar ETC Systems (TPS A/B correlation)
- Nissan / Honda / Toyota / Ford Drive-by-Wire Throttle Bodies (SAE J2012)

## Common Symptoms
- Immediate **Reduced Engine Power / Limp Mode** warning (`ETC` lightning bolt or wrench light) with dead or sluggish throttle
- High or hunting idle (`1,200–1,800 RPM`), stalling at stops, or inability to rev past `~2,000–2,500 RPM`
- Often returns after cold damp mornings, bumps (loose throttle pigtail), or low battery starts (`P0562`)

## Most Likely Root Causes
- **Fretted, oxidized, or loose 6-pin Electronic Throttle Body (`ETB`) connector pigtail** (#1 overlooked repair on GM/Chrysler/Nissan)
- Worn or moisture-contaminated internal **dual TPS tracks (`TPS1 / TPS2`)** inside the Electronic Throttle Body
- Heavy **black carbon ridge binding the throttle blade** around the bore so actual opening lags motor command
- Low **battery/charging voltage (`P0562`)** or shared **`5.0 V` sensor reference drop (`P0641`)** skewing `TPS1/TPS2`

## Tools & Parts Reference
- OBD-II live-data scanner (`TPS1` & `TPS2` voltage graph + Throttle/Idle Relearn function)
- Digital multimeter (`5.0 V` reference, ground & terminal pin-drag check)
- Throttle-body cleaner, lint-free rags & replacement OEM pigtail kit (if corroded)

## Step-by-Step Troubleshooting & Fix
1. If wiggling the throttle harness makes `TPS1/TPS2` spike—or pins look darkened/spread—install a new **OEM throttle-body connector pigtail kit** with staggered heat-shrink splices and dielectric contact lube.
2. Disconnect negative battery terminal, remove intake boot, and gently clean thick black carbon buildup from the **throttle bore and brass/aluminum blade edge** using throttle-body cleaner on a lint-free rag (avoid flooding the electronics housing!).
3. If the `5.0 V` ref, ground, and pigtail test solid yet `TPS1` and `TPS2` still diverge or glitch during sweeps, replace the **Electronic Throttle Body assembly** (or bolt-on TPS module where serviceable).
4. Clear `P2135` and **ALWAYS execute the factory Idle Air Volume / Throttle Body Relearn** (key-on wait / scan-tool relearn or drive cycle) so idle settles smoothly.

## Estimated Repair Cost Benchmark
| Currency | DIY Parts Only | Professional Repair (Parts + Labor) |
| --- | --- | --- |
| USD | $15–$260 | $220–$640 |
| GBP | £12–£210 | £175–£495 |
| CAD | CA$20–CA$340 | CA$290–CA$830 |
| EUR | €15–€235 | €195–€580 |
| CHF | CHF 18–CHF 285 | CHF 260–CHF 725 |

## Frequently Asked Questions
### Is it safe to drive when Reduced Engine Power (P2135) activates?
No—`P2135` locks the engine into **Limp Mode** with severely limited acceleration or sudden stalling, making highway merges and intersections unsafe until repaired.

### What is the difference between P2135 and P2138?
`P2135` (`TPS "A"/"B"`) occurs at the **Electronic Throttle Body under the hood**, whereas `P2138` (`APP "D"/"E"`) occurs inside the cabin at the **Accelerator Gas Pedal sensor**.


## Verified Official & Engineering References
- [US EPA On-Board Diagnostics (OBD) Standards](https://www.epa.gov/obd) (Regulation / Standard)
- [SAE International: SAE J2012 Diagnostic Trouble Code Standards](https://www.sae.org/standards/content/j2012/) (Regulation / Standard)
- [NHTSA Vehicle Safety & Emissions Recalls / TSB Portal](https://www.nhtsa.gov/recalls) (Official Support)
