FaultCodes.org
P0729OBD-IITransmission & DrivetrainTechnical Reference· Updated: Nov 22, 2026

P0729 Fault Code: Gear 6 Incorrect Ratio

OBD-II P0729 (Transmission & Drivetrain): Gear 6 Incorrect Ratio.

Quick AnswerHigh — Service Soon

OBD-II fault code P0729 indicates Gear 6 Incorrect Ratio. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $162–$3780.

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Professional Recommended
System
Transmission & Drivetrain
Professional Repair
$162 – $3,780

What This Fault Code Means

The transmission module divides input (turbine) speed by output speed and compares the result with the ratio of the commanded gear; a deviation means slip – a clutch or brake not holding, too little pressure – or a wrong gear. Thresholds: Ford more than 30 rpm off for 1.8 s three times (diesel 2023: over 20 % for 12 s), GM's 2006 tables and the Allison 1000 converter slip of 200–230 rpm for 2.25 s after one trip, Saab's Aisin boxes over 20 % twelve times without MIL. P0729 concerns sixth gear. Saab's Aisin six-speed also checks whether the actual ratio matches fourth or fifth – the sixth gear clutch is not holding and the box drops into another gear. Ford stores it only if the fault does not fit a particular solenoid (otherwise P0751 ff). On GM manual transmissions (LT4) it checks the gear position sensor instead.

Common Symptoms

  • Slipping or flare in sixth gear, engine speed higher than expected
  • Harsh or delayed shifts
  • Limp mode (Aisin: second gear and reverse only), transmission warning
  • Check engine light depending on manufacturer

Most Likely Root Causes

  • Fluid level too low or fluid worn or contaminated
  • Clutch for sixth gear worn (linings, piston seal)
  • Sticking shift or pressure valve, leaking valve body gasket, blocked passages
  • GM manual transmissions only: gear position sensor faulty or not learned

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0729.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Transmission Clutches.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0729?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Transmission Clutches.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Transmission Clutches.
  5. 5Clear fault memory and run a verification cycle to confirm P0729 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$57 – $1,588
Professional Repair (Parts + Labor)$162 – $3,780

Certified Technician Service Checklist

This fault involves sealed safety, gas, or high-voltage systems. Share these details when requesting a repair quote.

  • Share exact brand & fault code: P0729 (Transmission & Drivetrain)
  • Record appliance/boiler serial, model plate, or pressure reading before calling
  • Typical certified technician range: $162 – $3,780

Frequently Asked Questions

Is it safe to keep operating with fault code P0729?

Avoid prolonged operation until inspected to prevent secondary component damage.

How much does it cost to repair P0729?

DIY replacement parts average $57–$1588, while professional service averages $162–$3780.

Will resetting P0729 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0729 fault code meaningP0729 repair costhow to fix P0729

Manufacturer & Technical Reference

OBD-II Technical Reference (Transmission & Drivetrain)

Related Fault Codes

Auto & OBD-II →
P0729 Fault Code: Gear 6 Incorrect Ratio — Causes, Fixes & Cost | FaultCodes.org