FaultCodes.org
P0727OBD-IITransmission & DrivetrainTechnical Reference· Updated: Nov 22, 2026

P0727 Fault Code: Engine Speed Input Circuit No Signal

OBD-II P0727 (Transmission & Drivetrain): Engine Speed Input Circuit No Signal.

Quick AnswerHigh — Service Soon

OBD-II fault code P0727 indicates Engine Speed Input Circuit No Signal. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $65–$432.

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Moderate (Intermediate)
System
Transmission & Drivetrain
Professional Repair
$65 – $432

What This Fault Code Means

The transmission module needs engine speed for converter slip, shift quality and to check the turbine speed. Today it almost always arrives over CAN from the engine module with a validity flag; only GM's 2007 Allison 1000 tables show a separate engine speed sensor read by the transmission module. P0727 means the engine speed signal is missing although the transmission is turning. The Allison 1000 flags under 61 rpm for 4 s with turbine speed of 400 rpm or more, after two trips; Saab's 9-3 of 2000 input speed above 2000 rpm for more than 5 s without engine speed; a 2006 GM table the CAN engine speed failing to answer. The module then works without converter slip information, usually locks out the converter clutch and may enter limp mode.

Common Symptoms

  • Transmission warning lamp, possibly check engine light
  • Torque converter clutch locked out
  • Harsh shifts or limp mode
  • Often an engine code (crankshaft sensor) as well

Most Likely Root Causes

  • Engine speed wire or connector open, or own sensor (Allison) faulty
  • CAN communication between engine and transmission module disturbed
  • Crankshaft sensor fault in the engine module
  • Transmission module faulty

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0727.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Engine Speed Signal.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0727?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Engine Speed Signal.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Engine Speed Signal.
  5. 5Clear fault memory and run a verification cycle to confirm P0727 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$23 – $181
Professional Repair (Parts + Labor)$65 – $432

Frequently Asked Questions

Is it safe to keep operating with fault code P0727?

Avoid prolonged operation until inspected to prevent secondary component damage.

How much does it cost to repair P0727?

DIY replacement parts average $23–$181, while professional service averages $65–$432.

Will resetting P0727 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0727 fault code meaningP0727 repair costhow to fix P0727

Manufacturer & Technical Reference

OBD-II Technical Reference (Transmission & Drivetrain)

Related Fault Codes

Auto & OBD-II →
P0727 Fault Code: Engine Speed Input Circuit No Signal | FaultCodes.org