FaultCodes.org
P0722OBD-IITransmission & DrivetrainTechnical Reference· Updated: Nov 22, 2026

P0722 Fault Code: Output Shaft Speed Sensor Circuit No Signal

OBD-II P0722 (Transmission & Drivetrain): Output Shaft Speed Sensor Circuit No Signal.

Quick AnswerHigh — Service Soon

OBD-II fault code P0722 indicates Output Shaft Speed Sensor Circuit No Signal. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $86–$486.

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Moderate (Intermediate)
System
Transmission & Drivetrain
Professional Repair
$86 – $486

What This Fault Code Means

The output shaft speed sensor (Hall or inductive) reports the speed of the transmission output; it gives the gear ratio together with input speed and on many vehicles also the road speed for speedometer and cruise control. P0722 means the output speed signal is missing while the vehicle is driving. GM's 2025 modules flag under 60 rpm for 3.5–5 s with more than 50 Nm torque and check wheel speeds as well; a 2006 GM table flags no output pulse during 6000 input pulses; Ford under 100–200 rpm for 5–30 s; Saab's Aisin box from 4 km/h. GM rates it after one trip. The transmission goes into limp mode, and speedometer and cruise control may stop working. On GM's 10-speed, P0717 and P0722 together point to the shared sensor supply.

Common Symptoms

  • Speedometer reads 0
  • Limp mode or fixed gear
  • Warning lamp (MIL, transmission)
  • Cruise control not working

Most Likely Root Causes

  • Speed sensor faulty (Hall IC or coil open or shorted)
  • Connector or harness corroded, chafed or loose pins (with internal sensors also the pass-through connector)
  • Metal debris on the sensor magnet or damaged reluctor wheel
  • Transmission module or its sensor supply faulty

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0722.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Output Speed Sensor.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0722?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Output Speed Sensor.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Output Speed Sensor.
  5. 5Clear fault memory and run a verification cycle to confirm P0722 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$30 – $204
Professional Repair (Parts + Labor)$86 – $486

Frequently Asked Questions

Is it safe to keep operating with fault code P0722?

Avoid prolonged operation until inspected to prevent secondary component damage.

How much does it cost to repair P0722?

DIY replacement parts average $30–$204, while professional service averages $86–$486.

Will resetting P0722 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0722 fault code meaningP0722 repair costhow to fix P0722

Manufacturer & Technical Reference

OBD-II Technical Reference (Transmission & Drivetrain)

Related Fault Codes

Auto & OBD-II →
P0722 Fault Code: Output Shaft Speed Sensor Circuit No Signal | FaultCodes.org