FaultCodes.org
P0720OBD-IITransmission & DrivetrainTechnical Reference· Updated: Nov 22, 2026

P0720 Fault Code: Output Shaft Speed Sensor Circuit

OBD-II P0720 (Transmission & Drivetrain): Output Shaft Speed Sensor Circuit.

Quick AnswerHigh — Service Soon

OBD-II fault code P0720 indicates Output Shaft Speed Sensor Circuit. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $86–$486.

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Moderate (Intermediate)
System
Transmission & Drivetrain
Professional Repair
$86 – $486

What This Fault Code Means

The output shaft speed sensor (Hall or inductive) reports the speed of the transmission output; it gives the gear ratio together with input speed and on many vehicles also the road speed for speedometer and cruise control. P0720 is the general circuit code. Ford also uses it for 'no signal': while engine and turbine speed show the vehicle moving, the sensor reports under 100–200 rpm for 5–30 s; ZF's 6HP26 in Ford vehicles flags an open or short after 0.6 s. Subaru-based systems (Saab 9-2X) flag an impossible 255 km/h or 0 km/h while driving and light the MIL after two trips, substituting the other sensor. GM does not use P0720 but P0722. Speedometer and cruise control may fail, often with a vehicle speed code as well.

Common Symptoms

  • Speedometer drops out or jumps
  • Warning lamp, limp mode or fixed gear
  • Harsh shifts, cruise control not working

Most Likely Root Causes

  • Speed sensor faulty (Hall IC or coil open or shorted)
  • Connector or harness corroded, chafed or loose pins (with internal sensors also the pass-through connector)
  • Metal debris on the sensor magnet or damaged reluctor wheel
  • Transmission module or its sensor supply faulty

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0720.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Output Speed Sensor.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0720?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Output Speed Sensor.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Output Speed Sensor.
  5. 5Clear fault memory and run a verification cycle to confirm P0720 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$30 – $204
Professional Repair (Parts + Labor)$86 – $486

Frequently Asked Questions

Is it safe to keep operating with fault code P0720?

Avoid prolonged operation until inspected to prevent secondary component damage.

How much does it cost to repair P0720?

DIY replacement parts average $30–$204, while professional service averages $86–$486.

Will resetting P0720 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0720 fault code meaningP0720 repair costhow to fix P0720

Manufacturer & Technical Reference

OBD-II Technical Reference (Transmission & Drivetrain)

Related Fault Codes

Auto & OBD-II →
P0720 Fault Code: Output Shaft Speed Sensor Circuit — Fixes & Cost | FaultCodes.org