FaultCodes.org
P0718OBD-IITransmission & DrivetrainTechnical Reference· Updated: Nov 22, 2026

P0718 Fault Code: Input/Turbine Shaft Speed Sensor A Circuit Intermittent

OBD-II P0718 (Transmission & Drivetrain): Input/Turbine Shaft Speed Sensor A Circuit Intermittent.

Quick AnswerHigh — Service Soon

OBD-II fault code P0718 indicates Input/Turbine Shaft Speed Sensor A Circuit Intermittent. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $86–$486.

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Moderate (Intermediate)
System
Transmission & Drivetrain
Professional Repair
$86 – $486

What This Fault Code Means

The input or turbine shaft speed sensor – a Hall sensor with square-wave output or an inductive sensor with sine output – reports the speed behind the torque converter. With output and engine speed it gives the actual gear ratio, converter slip and shift timing. P0718 means the signal is present but jumps or drops out briefly. Ford's petrol modules from 2012 to 2023 count 200 turbine speed spikes above 400 rpm with at most 1.5 s between them in a forward gear. GM's Honda-built five-speed of 2006 flags jumps of more than 3 mph per 10 ms three times in 500 ms, after two trips; GM's own transmissions file such jumps under P0716 instead. Loose contacts and electrical interference are the usual causes; shifts become erratic and limp mode may follow at times.

Common Symptoms

  • Occasional harsh or unexpected shifts
  • Warning lamp
  • Converter clutch applies and releases unevenly
  • Limp mode at times

Most Likely Root Causes

  • Loose contact, corroded connector or chafing
  • Electrical interference (shielding, ground, added consumers)
  • Metal debris on the sensor or loose mounting
  • Sensor faulty internally (temperature-dependent)

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0718.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Input Speed Sensor.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0718?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Input Speed Sensor.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Input Speed Sensor.
  5. 5Clear fault memory and run a verification cycle to confirm P0718 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$30 – $204
Professional Repair (Parts + Labor)$86 – $486

Frequently Asked Questions

Is it safe to keep operating with fault code P0718?

Avoid prolonged operation until inspected to prevent secondary component damage.

How much does it cost to repair P0718?

DIY replacement parts average $30–$204, while professional service averages $86–$486.

Will resetting P0718 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0718 fault code meaningP0718 repair costhow to fix P0718

Manufacturer & Technical Reference

OBD-II Technical Reference (Transmission & Drivetrain)

Related Fault Codes

Auto & OBD-II →
P0718 Fault Code: Input/Turbine Shaft Speed Sensor… — Fixes & Cost | FaultCodes.org