FaultCodes.org
P0717OBD-IITransmission & DrivetrainTechnical Reference· Updated: Nov 22, 2026

P0717 Fault Code: Input/Turbine Shaft Speed Sensor A Circuit No Signal

OBD-II P0717 (Transmission & Drivetrain): Input/Turbine Shaft Speed Sensor A Circuit No Signal.

Quick AnswerHigh — Service Soon

OBD-II fault code P0717 indicates Input/Turbine Shaft Speed Sensor A Circuit No Signal. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $162–$1620.

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Professional Recommended
System
Transmission & Drivetrain
Professional Repair
$162 – $1,620

What This Fault Code Means

The input or turbine shaft speed sensor – a Hall sensor with square-wave output or an inductive sensor with sine output – reports the speed behind the torque converter. With output and engine speed it gives the actual gear ratio, converter slip and shift timing. P0717 means there is practically no input speed signal although the vehicle is driving under power. GM's 2025 modules flag under 200 rpm for more than 4 s with torque applied, the 6T70 under 50 rpm for 5 s, the Allison 1000 under 61 rpm with output above 500 rpm; Ford under 200 rpm for 5–30 s; all after one trip. GM calls it 'circuit low voltage', but means missing frequency. On GM's 10-speed both input and output sensors share a supply – P0717 together with P0722 points to that supply rather than two sensors.

Common Symptoms

  • Check engine and/or transmission warning lamp
  • Limp mode with fixed gear, harsh shifts
  • Torque converter clutch does not apply
  • Input speed shows 0 or implausible in the scan tool

Most Likely Root Causes

  • Speed sensor faulty (Hall IC or coil open or shorted)
  • Connector or harness corroded, chafed or loose pins (with internal sensors also the pass-through connector)
  • Metal debris on the sensor magnet or damaged reluctor wheel
  • Transmission module or its sensor supply faulty

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0717.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Input Speed Sensor.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0717?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Input Speed Sensor.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Input Speed Sensor.
  5. 5Clear fault memory and run a verification cycle to confirm P0717 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$57 – $680
Professional Repair (Parts + Labor)$162 – $1,620

Certified Technician Service Checklist

This fault involves sealed safety, gas, or high-voltage systems. Share these details when requesting a repair quote.

  • Share exact brand & fault code: P0717 (Transmission & Drivetrain)
  • Record appliance/boiler serial, model plate, or pressure reading before calling
  • Typical certified technician range: $162 – $1,620

Frequently Asked Questions

Is it safe to keep operating with fault code P0717?

Avoid prolonged operation until inspected to prevent secondary component damage.

How much does it cost to repair P0717?

DIY replacement parts average $57–$680, while professional service averages $162–$1620.

Will resetting P0717 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0717 fault code meaningP0717 repair costhow to fix P0717

Manufacturer & Technical Reference

OBD-II Technical Reference (Transmission & Drivetrain)

Related Fault Codes

Auto & OBD-II →
P0717 Fault Code: Input/Turbine Shaft Speed Sensor… — Fixes & Cost | FaultCodes.org