P0716 Fault Code: Input/Turbine Shaft Speed Sensor A Circuit Range/Performance
OBD-II P0716 (Transmission & Drivetrain): Input/Turbine Shaft Speed Sensor A Circuit Range/Performance.
OBD-II fault code P0716 indicates Input/Turbine Shaft Speed Sensor A Circuit Range/Performance. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $162–$1620.
- Safe to Operate?
- No — Risk of Damage
- DIY Difficulty
- Professional Recommended
- System
- Transmission & Drivetrain
- Professional Repair
- $162 – $1,620
What This Fault Code Means
The input or turbine shaft speed sensor – a Hall sensor with square-wave output or an inductive sensor with sine output – reports the speed behind the torque converter. With output and engine speed it gives the actual gear ratio, converter slip and shift timing. P0716 means a signal is present but implausible: too high, or dropping suddenly without recovering. GM's 2025 modules count drops of more than 650 rpm between 25 ms samples and fail after more than three; the 6T70 in the Saab 9-4X flags a 1350 rpm drop for 1 s; the 2007 Allison 1000 also detects noise and swapped sensor wires; all after one trip. Ford's 6R80 flags turbine speed above 7700 rpm. The 6T70 then runs only reverse and fifth gear, with maximum line pressure and no converter clutch.
Common Symptoms
- Check engine and/or transmission warning lamp
- Limp mode with fixed gear (6T70: reverse and fifth only)
- Harsh or delayed shifts
- Torque converter clutch locked out
Most Likely Root Causes
- Loose contact or chafing in the sensor circuit
- Sensor faulty, wrong air gap or metal debris
- Reluctor wheel or clutch drum damaged
- Sensor wires swapped after repair or interference
Diagnostic Checks Before Replacing Parts
Verify the exact faulty component before ordering replacements.
- 1Read stored freeze-frame data and companion codes alongside P0716.
- 2Inspect electrical connectors, fuses, and harnesses connected to Input Speed Sensor.
- 3Verify live sensor telemetry before ordering replacement components.
Interactive Symptom Triage
Answer 3 quick checks to narrow down the faulty component before spending money on parts.
Are any companion fault codes stored alongside P0716?
Step-by-Step Troubleshooting & Fix
- 1Scan for companion fault codes and address upstream circuit issues first.
- 2Visually inspect wiring harnesses, plugs, and hoses around Input Speed Sensor.
- 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
- 4Repair damaged wiring or install an OEM-grade replacement Input Speed Sensor.
- 5Clear fault memory and run a verification cycle to confirm P0716 does not return.
Estimated Repair Cost Benchmark
Typical DIY parts and certified technician labor ranges. Select a currency below.
| Repair Path | USD |
|---|---|
| DIY Parts Only | $57 – $680 |
| Professional Repair (Parts + Labor) | $162 – $1,620 |
Certified Technician Service Checklist
This fault involves sealed safety, gas, or high-voltage systems. Share these details when requesting a repair quote.
- Share exact brand & fault code: P0716 (Transmission & Drivetrain)
- Record appliance/boiler serial, model plate, or pressure reading before calling
- Typical certified technician range: $162 – $1,620
Frequently Asked Questions
Is it safe to keep operating with fault code P0716?
Avoid prolonged operation until inspected to prevent secondary component damage.
How much does it cost to repair P0716?
DIY replacement parts average $57–$680, while professional service averages $162–$1620.
Will resetting P0716 fix the problem permanently?
No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.
Related Searches & Questions
Manufacturer & Technical Reference
OBD-II Technical Reference (Transmission & Drivetrain)