FaultCodes.org
P0713OBD-IITransmission & DrivetrainTechnical Reference· Updated: Nov 22, 2026

P0713 Fault Code: Transmission Fluid Temperature Sensor A Circuit High

OBD-II P0713 (Transmission & Drivetrain): Transmission Fluid Temperature Sensor A Circuit High.

Quick AnswerHigh — Service Soon

OBD-II fault code P0713 indicates Transmission Fluid Temperature Sensor A Circuit High. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $86–$648.

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Moderate (Intermediate)
System
Transmission & Drivetrain
Professional Repair
$86 – $648

What This Fault Code Means

The transmission fluid temperature sensor is an NTC thermistor whose resistance falls as the fluid warms; the module feeds it with 5 V through a resistor. A low signal therefore means very hot or a short to ground, a high signal very cold or an open circuit. P0713 means the signal is too high – the sensor reads extremely cold, or the circuit is open or shorted to positive. GM's 2025 modules flag above 284 kΩ for 5 of 6 s after two trips; the 2007 Allison 1000 −45 °C or below for 2.5 s; Saab's AF40 below −43 °C; Ford above 4.6 V for 5–12 s without MIL. Many require prior running time or a warm engine so a genuine −40 °C cold start does not count (Allison: coolant above 20 °C; Saab: over 10 minutes of driving). The transmission then stays in its cold strategy: open converter clutch, late upshifts.

Common Symptoms

  • Fluid temperature shown around −40 °C
  • Converter clutch stays open, late upshifts
  • Higher fuel consumption
  • Check engine or transmission lamp depending on manufacturer

Most Likely Root Causes

  • Transmission connector loose or corroded, wire open
  • Sensor open internally
  • Signal wire shorted to positive
  • Control module faulty

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0713.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Transmission Fluid Temperature Sensor.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0713?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Transmission Fluid Temperature Sensor.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Transmission Fluid Temperature Sensor.
  5. 5Clear fault memory and run a verification cycle to confirm P0713 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$30 – $272
Professional Repair (Parts + Labor)$86 – $648

Frequently Asked Questions

Is it safe to keep operating with fault code P0713?

Avoid prolonged operation until inspected to prevent secondary component damage.

How much does it cost to repair P0713?

DIY replacement parts average $30–$272, while professional service averages $86–$648.

Will resetting P0713 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0713 fault code meaningP0713 repair costhow to fix P0713

Manufacturer & Technical Reference

OBD-II Technical Reference (Transmission & Drivetrain)

Related Fault Codes

Auto & OBD-II →
P0713 Fault Code: Transmission Fluid Temperature… — Fixes & Cost | FaultCodes.org