FaultCodes.org
P0710OBD-IITransmission & DrivetrainTechnical Reference· Updated: Nov 22, 2026

P0710 Fault Code: Transmission Fluid Temperature Sensor A Circuit

OBD-II P0710 (Transmission & Drivetrain): Transmission Fluid Temperature Sensor A Circuit.

Quick AnswerHigh — Service Soon

OBD-II fault code P0710 indicates Transmission Fluid Temperature Sensor A Circuit. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $86–$648.

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Moderate (Intermediate)
System
Transmission & Drivetrain
Professional Repair
$86 – $648

What This Fault Code Means

The transmission fluid temperature sensor is an NTC thermistor whose resistance falls as the fluid warms; the module feeds it with 5 V through a resistor. A low signal therefore means very hot or a short to ground, a high signal very cold or an open circuit. P0710 is the general circuit code used when a manufacturer does not separate low and high. Subaru-based systems (Saab 9-2X) flag 0.1 V or less or 4.7 V or more, light the MIL after two consecutive trips and use 80 °C as substitute. Ford's 2023 diesels use P0710 alongside P0712/P0713 for open and short circuits, without MIL, after 5–12 s, substituting coolant temperature. GM uses only the split codes. With the substitute value the shift quality suffers: harsh shifts and a late converter clutch.

Common Symptoms

  • Harsh or late shifts
  • Torque converter clutch applies late or not at all
  • Check engine or transmission lamp depending on manufacturer
  • Implausible fluid temperature in the scan tool

Most Likely Root Causes

  • Fluid temperature sensor faulty (often part of the internal harness or valve body)
  • Transmission connector leaking or corroded, oil in the connector
  • Wire open or shorted
  • Transmission or engine module faulty

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0710.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Transmission Fluid Temperature Sensor.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0710?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Transmission Fluid Temperature Sensor.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Transmission Fluid Temperature Sensor.
  5. 5Clear fault memory and run a verification cycle to confirm P0710 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$30 – $272
Professional Repair (Parts + Labor)$86 – $648

Frequently Asked Questions

Is it safe to keep operating with fault code P0710?

Avoid prolonged operation until inspected to prevent secondary component damage.

How much does it cost to repair P0710?

DIY replacement parts average $30–$272, while professional service averages $86–$648.

Will resetting P0710 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0710 fault code meaningP0710 repair costhow to fix P0710

Manufacturer & Technical Reference

OBD-II Technical Reference (Transmission & Drivetrain)

Related Fault Codes

Auto & OBD-II →
P0710 Fault Code: Transmission Fluid Temperature Sensor A Circuit | FaultCodes.org