P049E Fault Code: EGR B Control Position Exceeded Learning Limit
OBD-II P049E (EVAP Emissions Control): EGR B Control Position Exceeded Learning Limit.
OBD-II fault code P049E indicates EGR B Control Position Exceeded Learning Limit. Usually safe for short trips if no severe drivability or safety warnings are active. Typical professional repair costs $43–$1080.
- Safe to Operate?
- Yes (Short Term)
- DIY Difficulty
- Professional Recommended
- System
- EVAP Emissions Control
- Professional Repair
- $43 – $1,080
What This Fault Code Means
Exhaust gas recirculation (EGR) routes part of the exhaust back into the intake to lower combustion temperature and NOx. Circuit B is the second EGR path; on diesels with two circuits it is the low-pressure EGR, which takes exhaust after the particulate filter and feeds it in before the turbo compressor (GM diesels 2016–18, FCA's 2.2 and 3.0 diesels). P049E is the counterpart of P049D for valve B: the learned zero point of its position sensor lies outside the permitted window. GM lists it only in a fault group of its low-pressure EGR (whose position sensor is sensor C there, P044C/P044D), and in the 2016 calibration it is explicitly disabled; thresholds are not published. The description therefore follows GM's P049D strategy by analogy. Low-pressure EGR position control is then switched off.
Common Symptoms
- Check engine light on
- EGR switched off, usually no noticeable change
- Higher NOx
Most Likely Root Causes
- Low-pressure EGR valve sooted, does not close fully
- Position sensor of the low-pressure valve faulty or shifted
- Valve replaced without teaching in
- Harness or connector of the low-pressure valve
Diagnostic Checks Before Replacing Parts
Verify the exact faulty component before ordering replacements.
- 1Read stored freeze-frame data and companion codes alongside P049E.
- 2Inspect electrical connectors, fuses, and harnesses connected to Low Pressure Egr Valve.
- 3Verify live sensor telemetry before ordering replacement components.
Interactive Symptom Triage
Answer 3 quick checks to narrow down the faulty component before spending money on parts.
Are any companion fault codes stored alongside P049E?
Step-by-Step Troubleshooting & Fix
- 1Scan for companion fault codes and address upstream circuit issues first.
- 2Visually inspect wiring harnesses, plugs, and hoses around Low Pressure Egr Valve.
- 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
- 4Repair damaged wiring or install an OEM-grade replacement Low Pressure Egr Valve.
- 5Clear fault memory and run a verification cycle to confirm P049E does not return.
Estimated Repair Cost Benchmark
Typical DIY parts and certified technician labor ranges. Select a currency below.
| Repair Path | USD |
|---|---|
| DIY Parts Only | $16 – $454 |
| Professional Repair (Parts + Labor) | $43 – $1,080 |
Certified Technician Service Checklist
This fault involves sealed safety, gas, or high-voltage systems. Share these details when requesting a repair quote.
- Share exact brand & fault code: P049E (EVAP Emissions Control)
- Record appliance/boiler serial, model plate, or pressure reading before calling
- Typical certified technician range: $43 – $1,080
Frequently Asked Questions
Is it safe to keep operating with fault code P049E?
Usually safe for short trips if no severe drivability or safety warnings are active.
How much does it cost to repair P049E?
DIY replacement parts average $16–$454, while professional service averages $43–$1080.
Will resetting P049E fix the problem permanently?
No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.
Related Searches & Questions
Manufacturer & Technical Reference
OBD-II Technical Reference (EVAP Emissions Control)