FaultCodes.org
P049COBD-IIEVAP Emissions ControlTechnical Reference· Updated: Nov 22, 2026

P049C Fault Code: EGR B Flow Excessive Detected

OBD-II P049C (EVAP Emissions Control): EGR B Flow Excessive Detected.

Quick AnswerLow — Minor Issue

OBD-II fault code P049C indicates EGR B Flow Excessive Detected. Usually safe for short trips if no severe drivability or safety warnings are active. Typical professional repair costs $162–$1620.

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Professional Recommended
System
EVAP Emissions Control
Professional Repair
$162 – $1,620

What This Fault Code Means

Exhaust gas recirculation (EGR) routes part of the exhaust back into the intake to lower combustion temperature and NOx. Circuit B is the second EGR path; on diesels with two circuits it is the low-pressure EGR, which takes exhaust after the particulate filter and feeds it in before the turbo compressor (GM diesels 2016–18, FCA's 2.2 and 3.0 diesels). P049C means too much flow in circuit B – fresh air mass drops further than modelled, or EGR flows with the low-pressure valve closed; CARB explicitly requires a leaking valve to be detected. No manufacturer document available to us uses P049C; the closest is FCA's P045E for a low-pressure valve stuck open. Smoke, lack of power and rough idle follow, and low-pressure EGR is switched off.

Common Symptoms

  • Check engine light on
  • Lack of power, black smoke
  • Rough idle or misfire, in extreme cases stalling

Most Likely Root Causes

  • Low-pressure EGR valve stuck open or not sealing (soot)
  • Position sensor B implausible (valve seemingly closed)
  • Leak between exhaust side and intake
  • Air mass meter reading too low

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P049C.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Low Pressure Egr Valve.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P049C?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Low Pressure Egr Valve.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Low Pressure Egr Valve.
  5. 5Clear fault memory and run a verification cycle to confirm P049C does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$57 – $680
Professional Repair (Parts + Labor)$162 – $1,620

Certified Technician Service Checklist

This fault involves sealed safety, gas, or high-voltage systems. Share these details when requesting a repair quote.

  • Share exact brand & fault code: P049C (EVAP Emissions Control)
  • Record appliance/boiler serial, model plate, or pressure reading before calling
  • Typical certified technician range: $162 – $1,620

Frequently Asked Questions

Is it safe to keep operating with fault code P049C?

Usually safe for short trips if no severe drivability or safety warnings are active.

How much does it cost to repair P049C?

DIY replacement parts average $57–$680, while professional service averages $162–$1620.

Will resetting P049C fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P049C fault code meaningP049C repair costhow to fix P049C

Manufacturer & Technical Reference

OBD-II Technical Reference (EVAP Emissions Control)

Related Fault Codes

Auto & OBD-II →
P049C Fault Code: EGR B Flow Excessive Detected — Fixes & Cost | FaultCodes.org