FaultCodes.org
P0499OBD-IIEVAP Emissions ControlTechnical Reference· Updated: Nov 22, 2026

P0499 Fault Code: EVAP System Vent Valve Control Circuit High

OBD-II P0499 (EVAP Emissions Control): EVAP System Vent Valve Control Circuit High.

Quick AnswerLow — Minor Issue

OBD-II fault code P0499 indicates EVAP System Vent Valve Control Circuit High. Usually safe for short trips if no severe drivability or safety warnings are active. Typical professional repair costs $43–$270.

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Easy (Basic Tools)
System
EVAP Emissions Control
Professional Repair
$43 – $270

What This Fault Code Means

The evaporative emission (EVAP) system stores fuel vapour from the tank in a charcoal canister; a purge valve lets the engine draw it off, and a vent valve opens the canister to fresh air. The vent valve is normally open and switched to ground by the module (GM scheme P0449/P0498/P0499; Ford uses P0446). P0499 means the control wire is shorted to positive: with the driver on the output stays high – GM sees 0.5 Ω or less to the supply, Saab above 4.6 V; MIL after two trips. The valve then cannot close, the system cannot be sealed, and the leak tests are suspended because they would otherwise report a large leak.

Common Symptoms

  • Check engine light on
  • EVAP readiness not set
  • Usually no change in driving

Most Likely Root Causes

  • Control wire touching battery positive or the valve supply (chafed harness)
  • Vent valve coil with shorted turns, driver switches off
  • Moisture or corrosion in the connector
  • Driver in the engine module

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0499.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Evap Vent Valve.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0499?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Evap Vent Valve.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Evap Vent Valve.
  5. 5Clear fault memory and run a verification cycle to confirm P0499 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$16 – $113
Professional Repair (Parts + Labor)$43 – $270

Frequently Asked Questions

Is it safe to keep operating with fault code P0499?

Usually safe for short trips if no severe drivability or safety warnings are active.

How much does it cost to repair P0499?

DIY replacement parts average $16–$113, while professional service averages $43–$270.

Will resetting P0499 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0499 fault code meaningP0499 repair costhow to fix P0499

Manufacturer & Technical Reference

OBD-II Technical Reference (EVAP Emissions Control)

Related Fault Codes

Auto & OBD-II →
P0499 Fault Code: EVAP System Vent Valve Control Circuit High | FaultCodes.org