FaultCodes.org
P0498OBD-IIEVAP Emissions ControlTechnical Reference· Updated: Nov 22, 2026

P0498 Fault Code: EVAP System Vent Valve Control Circuit Low

OBD-II P0498 (EVAP Emissions Control): EVAP System Vent Valve Control Circuit Low.

Quick AnswerLow — Minor Issue

OBD-II fault code P0498 indicates EVAP System Vent Valve Control Circuit Low. Usually safe for short trips if no severe drivability or safety warnings are active. Typical professional repair costs $43–$270.

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Easy (Basic Tools)
System
EVAP Emissions Control
Professional Repair
$43 – $270

What This Fault Code Means

The evaporative emission (EVAP) system stores fuel vapour from the tank in a charcoal canister; a purge valve lets the engine draw it off, and a vent valve opens the canister to fresh air. The vent valve is normally open and switched to ground by the module; P0449 (open), P0498 and P0499 form the newer code scheme for its circuit, used mainly by GM and Saab models with GM engines, while Ford uses P0446. P0498 means the control wire is shorted to ground: GM sees 0.5 Ω or less to ground with the driver off (20 of 25 samples), Saab below 2.6 V – MIL after two trips. The valve is then permanently energised and closed, so the tank is not vented and refuelling becomes difficult.

Common Symptoms

  • Check engine light on
  • Refuelling difficult, nozzle clicks off
  • Vacuum noise when opening the fuel cap

Most Likely Root Causes

  • Vent valve control wire chafed against ground (underbody, tank area)
  • Vent valve coil shorted internally
  • Corrosion or water in the connector
  • Driver in the engine module

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0498.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Evap Vent Valve.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0498?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Evap Vent Valve.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Evap Vent Valve.
  5. 5Clear fault memory and run a verification cycle to confirm P0498 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$16 – $113
Professional Repair (Parts + Labor)$43 – $270

Frequently Asked Questions

Is it safe to keep operating with fault code P0498?

Usually safe for short trips if no severe drivability or safety warnings are active.

How much does it cost to repair P0498?

DIY replacement parts average $16–$113, while professional service averages $43–$270.

Will resetting P0498 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0498 fault code meaningP0498 repair costhow to fix P0498

Manufacturer & Technical Reference

OBD-II Technical Reference (EVAP Emissions Control)

Related Fault Codes

Auto & OBD-II →
P0498 Fault Code: EVAP System Vent Valve Control Circuit Low | FaultCodes.org