FaultCodes.org
P044BOBD-IIEVAP Emissions ControlTechnical Reference· Updated: Nov 22, 2026

P044B Fault Code: EGR Sensor C Circuit Range/Performance

OBD-II P044B (EVAP Emissions Control): EGR Sensor C Circuit Range/Performance.

Quick AnswerLow — Minor Issue

OBD-II fault code P044B indicates EGR Sensor C Circuit Range/Performance. Usually safe for short trips if no severe drivability or safety warnings are active. Typical professional repair costs $43–$270.

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Easy (Basic Tools)
System
EVAP Emissions Control
Professional Repair
$43 – $270

What This Fault Code Means

Exhaust gas recirculation (EGR) routes part of the exhaust back into the intake to lower combustion temperature and NOx. What EGR sensor C is depends on the maker: on Ford petrol engines from 2020 it is the DPFE sensor, which measures the pressure drop across an orifice in the EGR pipe (sensor A there is the valve position sensor); GM diesels assign it to the position sensor of a low-pressure EGR valve, but only within fault groups. P044B means its signal is electrically valid but implausible – for example a pressure difference with the valve closed, or no reaction when it opens. No manufacturer document available to us uses this code; Ford checks the DPFE plausibility under its own codes P139A–P139C (hoses swapped, front or rear hose off or blocked). EGR flow diagnosis is then suspended.

Common Symptoms

  • Check engine light on
  • Usually no change in driving
  • EGR readiness not set, EGR possibly switched off

Most Likely Root Causes

  • Pressure hoses off, swapped or blocked (soot, condensate)
  • Sensor zero point drifted
  • Orifice or EGR pipe coked
  • Contact resistance in the connector

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P044B.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Egr Sensor C.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P044B?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Egr Sensor C.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Egr Sensor C.
  5. 5Clear fault memory and run a verification cycle to confirm P044B does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$16 – $113
Professional Repair (Parts + Labor)$43 – $270

Frequently Asked Questions

Is it safe to keep operating with fault code P044B?

Usually safe for short trips if no severe drivability or safety warnings are active.

How much does it cost to repair P044B?

DIY replacement parts average $16–$113, while professional service averages $43–$270.

Will resetting P044B fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P044B fault code meaningP044B repair costhow to fix P044B

Manufacturer & Technical Reference

OBD-II Technical Reference (EVAP Emissions Control)

Related Fault Codes

Auto & OBD-II →
P044B Fault Code: EGR Sensor C Circuit Range/Performance | FaultCodes.org