FaultCodes.org
P0444OBD-IIEVAP Emissions ControlTechnical Reference· Updated: Nov 22, 2026

P0444 Fault Code: EVAP System Purge Control Valve A Circuit Open

OBD-II P0444 (EVAP Emissions Control): EVAP System Purge Control Valve A Circuit Open.

Quick AnswerLow — Minor Issue

OBD-II fault code P0444 indicates EVAP System Purge Control Valve A Circuit Open. Usually safe for short trips if no severe drivability or safety warnings are active. Typical professional repair costs $43–$216.

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Easy (Basic Tools)
System
EVAP Emissions Control
Professional Repair
$43 – $216

What This Fault Code Means

The evaporative emission (EVAP) system stores fuel vapour from the tank in a charcoal canister; a purge valve lets the engine draw it off, and a vent valve opens the canister to fresh air. P0444 belongs to the older scheme of circuit, open and shorted codes for purge valve A; Saab's Trionic T7 and VW use it, while GM reports an open circuit as P0443 and Ford covers everything in P0443. Saab checks with the output switched off: below 2 V the supply through the coil is missing or the line is grounded – Saab combines both under P0444, sets it after about 1 s and pauses the check until the next drive. Purging then stops.

Common Symptoms

  • Check engine light on
  • Possibly fuel smell
  • EVAP monitors do not run

Most Likely Root Causes

  • Purge valve connector off or corroded
  • Valve coil open
  • Supply wire, fuse, main relay or control wire open
  • Control wire shorted to ground (Saab definition)

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0444.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Evap Purge Valve.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0444?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Evap Purge Valve.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Evap Purge Valve.
  5. 5Clear fault memory and run a verification cycle to confirm P0444 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$16 – $91
Professional Repair (Parts + Labor)$43 – $216

Frequently Asked Questions

Is it safe to keep operating with fault code P0444?

Usually safe for short trips if no severe drivability or safety warnings are active.

How much does it cost to repair P0444?

DIY replacement parts average $16–$91, while professional service averages $43–$216.

Will resetting P0444 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0444 fault code meaningP0444 repair costhow to fix P0444

Manufacturer & Technical Reference

OBD-II Technical Reference (EVAP Emissions Control)

Related Fault Codes

Auto & OBD-II →
P0444 Fault Code: EVAP System Purge Control Valve A Circuit Open | FaultCodes.org