FaultCodes.org
P0443OBD-IIEVAP Emissions ControlTechnical Reference· Updated: Nov 22, 2026

P0443 Fault Code: EVAP System Purge Control Valve A Circuit

OBD-II P0443 (EVAP Emissions Control): EVAP System Purge Control Valve A Circuit.

Quick AnswerLow — Minor Issue

OBD-II fault code P0443 indicates EVAP System Purge Control Valve A Circuit. Usually safe for short trips if no severe drivability or safety warnings are active. Typical professional repair costs $43–$270.

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Easy (Basic Tools)
System
EVAP Emissions Control
Professional Repair
$43 – $270

What This Fault Code Means

The evaporative emission (EVAP) system stores fuel vapour from the tank in a charcoal canister; a purge valve lets the engine draw it off, and a vent valve opens the canister to fresh air. P0443 is the electrical check of purge valve A, which the module switches to ground in pulses; it compares the driver's feedback voltage with the commanded state. GM uses it for an open circuit (200 kΩ or more, 20 of 25 samples, MIL after two trips) and reports shorts as P0458/P0459; Ford covers open and short in P0443 (5 s). Purging then stops, the canister is no longer regenerated, and the leak and purge monitors are suspended.

Common Symptoms

  • Check engine light on
  • Possibly fuel smell (no purging)
  • EVAP leak test does not run

Most Likely Root Causes

  • Purge valve connector corroded, loose or off
  • Purge valve coil open or shorted
  • Control wire broken or chafed, or supply missing (fuse, main relay)
  • Driver in the engine module

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0443.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Evap Purge Valve.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0443?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Evap Purge Valve.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Evap Purge Valve.
  5. 5Clear fault memory and run a verification cycle to confirm P0443 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$16 – $113
Professional Repair (Parts + Labor)$43 – $270

Frequently Asked Questions

Is it safe to keep operating with fault code P0443?

Usually safe for short trips if no severe drivability or safety warnings are active.

How much does it cost to repair P0443?

DIY replacement parts average $16–$113, while professional service averages $43–$270.

Will resetting P0443 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0443 fault code meaningP0443 repair costhow to fix P0443

Manufacturer & Technical Reference

OBD-II Technical Reference (EVAP Emissions Control)

Related Fault Codes

Auto & OBD-II →
P0443 Fault Code: EVAP System Purge Control Valve A Circuit | FaultCodes.org