FaultCodes.org
P043EOBD-IICatalytic & Exhaust EmissionsTechnical Reference· Updated: Nov 22, 2026

P043E Fault Code: EVAP System Leak Detection Reference Orifice Low Flow

OBD-II P043E (Catalytic & Exhaust Emissions): EVAP System Leak Detection Reference Orifice Low Flow.

Quick AnswerModerate — Plan Repair

OBD-II fault code P043E indicates EVAP System Leak Detection Reference Orifice Low Flow. Usually safe for short trips if no severe drivability or safety warnings are active. Typical professional repair costs $43–$648.

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Moderate (Intermediate)
System
Catalytic & Exhaust Emissions
Professional Repair
$43 – $648

What This Fault Code Means

The evaporative emission (EVAP) system stores fuel vapour from the tank in a charcoal canister; a purge valve lets the engine draw it off, and a vent valve opens the canister to fresh air. Systems with a leak detection pump (Bosch DM-TL at VW, Audi, BMW and Maserati, Denso's canister pump module at Toyota/Lexus) first measure a reference value with the pump working only through a built-in 0.5 mm (0.020 in) orifice; it is the yardstick for the small-leak test that CARB requires. P043E means the reference measurement shows too little flow – the vacuum (or with DM-TL the pressure and pump current) becomes stronger than expected, so the orifice or reference path is partly blocked, often by dirt or liquid after overfilling. GM and Ford do not use the code; Maserati fixed false triggering with software.

Common Symptoms

  • Check engine light on
  • EVAP leak test does not run, readiness not set
  • Usually no change in driving

Most Likely Root Causes

  • Reference orifice or pump module dirty or blocked by liquid (overfilled tank, splash water)
  • Leak detection pump faulty (weak or blocking pump, changeover valve stuck)
  • Engine module software (false detection)
  • Pump connector or supply (voltage dip)

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P043E.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Evap Leak Detection Pump.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P043E?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Evap Leak Detection Pump.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Evap Leak Detection Pump.
  5. 5Clear fault memory and run a verification cycle to confirm P043E does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$16 – $272
Professional Repair (Parts + Labor)$43 – $648

Frequently Asked Questions

Is it safe to keep operating with fault code P043E?

Usually safe for short trips if no severe drivability or safety warnings are active.

How much does it cost to repair P043E?

DIY replacement parts average $16–$272, while professional service averages $43–$648.

Will resetting P043E fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P043E fault code meaningP043E repair costhow to fix P043E

Manufacturer & Technical Reference

OBD-II Technical Reference (Catalytic & Exhaust Emissions)

Related Fault Codes

Auto & OBD-II →
P043E Fault Code: EVAP System Leak Detection… — Fixes & Cost | FaultCodes.org