FaultCodes.org
P0322OBD-IIIgnition & Misfire SystemTechnical Reference· Updated: Nov 22, 2026

P0322 Fault Code: Ignition/Distributor Engine Speed Input Circuit No Signal

OBD-II P0322 (Ignition & Misfire System): Ignition/Distributor Engine Speed Input Circuit No Signal.

Quick AnswerHigh — Service Soon

OBD-II fault code P0322 indicates Ignition/Distributor Engine Speed Input Circuit No Signal. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $65–$432.

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Moderate (Intermediate)
System
Ignition & Misfire System
Professional Repair
$65 – $432

What This Fault Code Means

P0322 means the speed and reference input of the ignition – today the crankshaft position sensor – delivers no signal although the engine is turning. Ford proves the rotation with the camshaft sensor: if it shows more than one engine revolution without a crank signal (from 500 rpm, detected within 5 s), Ford sets P0322 or, depending on the engine, P0335; with electronic throttle the throttle software adds P2106 and goes into limp mode. Without a crank signal there is no ignition or injection, so the engine stalls or does not start. Saab's Motronic 2.8.1 (900 V6) sets P0322 when the engine fails to start; its inductive sensor should measure 500–600 Ω and give 2–5 V AC while cranking. Systems without a camshaft-based check may store no code at all on a total failure.

Common Symptoms

  • Engine cranks but does not start
  • Engine stalls while driving
  • Tachometer shows zero
  • Check engine light on, with electronic throttle limp mode (P2106)

Most Likely Root Causes

  • Crankshaft position sensor failed (often heat-related)
  • Open or short in signal, ground or 5 V supply, corroded connector
  • Sensor loose, air gap too large or tone wheel damaged
  • 5 V reference pulled down by another sensor on the same supply
  • Engine module

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0322.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Crankshaft Position Sensor.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0322?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Crankshaft Position Sensor.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Crankshaft Position Sensor.
  5. 5Clear fault memory and run a verification cycle to confirm P0322 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$23 – $181
Professional Repair (Parts + Labor)$65 – $432

Frequently Asked Questions

Is it safe to keep operating with fault code P0322?

Avoid prolonged operation until inspected to prevent secondary component damage.

How much does it cost to repair P0322?

DIY replacement parts average $23–$181, while professional service averages $65–$432.

Will resetting P0322 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0322 fault code meaningP0322 repair costhow to fix P0322

Manufacturer & Technical Reference

OBD-II Technical Reference (Ignition & Misfire System)

Related Fault Codes

Auto & OBD-II →
P0322 Fault Code: Ignition/Distributor Engine Speed… — Fixes & Cost | FaultCodes.org