FaultCodes.org
P0320OBD-IIIgnition & Misfire SystemTechnical Reference· Updated: Nov 22, 2026

P0320 Fault Code: Ignition/Distributor Engine Speed Input Circuit

OBD-II P0320 (Ignition & Misfire System): Ignition/Distributor Engine Speed Input Circuit.

Quick AnswerHigh — Service Soon

OBD-II fault code P0320 indicates Ignition/Distributor Engine Speed Input Circuit. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $54–$378.

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Moderate (Intermediate)
System
Ignition & Misfire System
Professional Repair
$54 – $378

What This Fault Code Means

P0320 originally covered the engine speed signal from the distributor or ignition module to the engine module (early OBD II); today Ford's engine module evaluates the crankshaft sensor directly and uses this code for it. Ford checks continuously from 200–500 rpm and sets it within 5 s when the number of teeth after the gap is wrong, the tooth time is implausible (below 30 or above 9,000 rpm) or the gap appears in the wrong place; fuel and spark are then cut briefly to resynchronise, and on electronic throttle P2106 limits power. Some Ford engines use P0339 instead. Typical causes are a faulty crankshaft sensor, interference in the wiring or a damaged tone wheel.

Common Symptoms

  • Check engine light on
  • Engine dies or stumbles briefly
  • Starting problems, tachometer twitching
  • Reduced power on electronic throttle (Ford P2106)

Most Likely Root Causes

  • Crankshaft or distributor speed sensor faulty or wrong air gap
  • Wiring, connector or shielding disturbed (loose contact, interference from ignition or radios)
  • Tone wheel damaged or dirty (missing tooth, metal chips)
  • Ignition module faulty on older vehicles
  • Engine module faulty

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0320.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Crankshaft Position Sensor.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0320?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Crankshaft Position Sensor.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Crankshaft Position Sensor.
  5. 5Clear fault memory and run a verification cycle to confirm P0320 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$19 – $159
Professional Repair (Parts + Labor)$54 – $378

Frequently Asked Questions

Is it safe to keep operating with fault code P0320?

Avoid prolonged operation until inspected to prevent secondary component damage.

How much does it cost to repair P0320?

DIY replacement parts average $19–$159, while professional service averages $54–$378.

Will resetting P0320 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0320 fault code meaningP0320 repair costhow to fix P0320

Manufacturer & Technical Reference

OBD-II Technical Reference (Ignition & Misfire System)

Related Fault Codes

Auto & OBD-II →
P0320 Fault Code: Ignition/Distributor Engine Speed Input Circuit | FaultCodes.org