FaultCodes.org
P0318OBD-IIIgnition & Misfire SystemTechnical Reference· Updated: Nov 22, 2026

P0318 Fault Code: Rough Road Sensor A Signal Circuit

OBD-II P0318 (Ignition & Misfire System): Rough Road Sensor A Signal Circuit.

Quick AnswerHigh — Service Soon

OBD-II fault code P0318 indicates Rough Road Sensor A Signal Circuit. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $54–$432.

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Moderate (Intermediate)
System
Ignition & Misfire System
Professional Repair
$54 – $432

What This Fault Code Means

Misfire detection works from crankshaft speed fluctuations, which rough roads also cause. CARB therefore allows misfire detection to pause on rough roads; many engines take a rough-road signal from the wheel speeds of the ABS module, a Ford patent describes such a detector. P0318 means rough-road signal A is missing or invalid. On GM engines (documented in Saab service information for the 1.6 turbo) the brake control module sends wheel speed over the data bus; the code sets between 1,520 and 4,000 rpm when that module reports a wheel speed sensor fault or no signal arrives for more than 5 s. GM files it without the warning light. Misfire detection then runs without its rough-road filter. ABS or stability warnings and further codes often appear at the same time.

Common Symptoms

  • Service message (GM without warning light)
  • Often ABS or stability warning at the same time
  • Driving unaffected

Most Likely Root Causes

  • Wheel speed sensor or wiring faulty – the brake module passes on the fault
  • Communication between engine and brake module lost (CAN, connector, supply)
  • Brake control module faulty
  • Separate rough-road sensor faulty, where fitted

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0318.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Wheel Speed Sensors.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0318?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Wheel Speed Sensors.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Wheel Speed Sensors.
  5. 5Clear fault memory and run a verification cycle to confirm P0318 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$19 – $181
Professional Repair (Parts + Labor)$54 – $432

Frequently Asked Questions

Is it safe to keep operating with fault code P0318?

Avoid prolonged operation until inspected to prevent secondary component damage.

How much does it cost to repair P0318?

DIY replacement parts average $19–$181, while professional service averages $54–$432.

Will resetting P0318 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0318 fault code meaningP0318 repair costhow to fix P0318

Manufacturer & Technical Reference

OBD-II Technical Reference (Ignition & Misfire System)

Related Fault Codes

Auto & OBD-II →
P0318 Fault Code: Rough Road Sensor A Signal Circuit — Fixes & Cost | FaultCodes.org