P0310 Fault Code: Cylinder 10 Misfire Detected
OBD-II P0310 (Ignition & Misfire System): Cylinder 10 Misfire Detected.
OBD-II fault code P0310 indicates Cylinder 10 Misfire Detected. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $43–$864.
- Safe to Operate?
- No — Risk of Damage
- DIY Difficulty
- Easy (Basic Tools)
- System
- Ignition & Misfire System
- Professional Repair
- $43 – $864
What This Fault Code Means
The engine module detects misfire from crankshaft speed: a cylinder that does not fire gives no acceleration impulse. At a catalyst-damaging rate (CARB: at least 5 % per 200 revolutions) the warning light flashes; at an emissions-relevant rate (at least 1 % per 1,000 revolutions – GM about 2–5 %, Ford 0.9–1.5 %) it comes on after two trips. Ford and GM may shut off a misfiring cylinder's injector to protect the catalyst. P0310 means more than 90 % of the detected misfires fall on cylinder 10. Usual causes are the ignition coil or spark plug of that cylinder, its injector, or low compression; a quick test is to swap coil or plug with a neighbouring cylinder and see whether the misfire moves. Cylinder 10 exists on ten-cylinder engines such as Ford's 6.8 litre V10; there an under-torqued crankshaft pulley bolt and engine software caused false misfire codes on all cylinders.
Common Symptoms
- Check engine light on, flashing at a catalyst-damaging rate
- Rough idle, jerking, vibration
- Loss of power, hesitation
- Smell of unburnt fuel, higher consumption
Most Likely Root Causes
- Ignition coil of cylinder 10 faulty (coil, connector, ground)
- Spark plug of cylinder 10 worn, sooted, cracked or wrongly gapped
- Injector of cylinder 10 clogged or leaking, or its control
- Low compression on cylinder 10 (valve, rings, head gasket) or local false air
- Water or oil in the plug well
Diagnostic Checks Before Replacing Parts
Verify the exact faulty component before ordering replacements.
- 1Read stored freeze-frame data and companion codes alongside P0310.
- 2Inspect electrical connectors, fuses, and harnesses connected to Ignition Coil Cylinder 10.
- 3Verify live sensor telemetry before ordering replacement components.
Interactive Symptom Triage
Answer 3 quick checks to narrow down the faulty component before spending money on parts.
Are any companion fault codes stored alongside P0310?
Step-by-Step Troubleshooting & Fix
- 1Scan for companion fault codes and address upstream circuit issues first.
- 2Visually inspect wiring harnesses, plugs, and hoses around Ignition Coil Cylinder 10.
- 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
- 4Repair damaged wiring or install an OEM-grade replacement Ignition Coil Cylinder 10.
- 5Clear fault memory and run a verification cycle to confirm P0310 does not return.
Estimated Repair Cost Benchmark
Typical DIY parts and certified technician labor ranges. Select a currency below.
| Repair Path | USD |
|---|---|
| DIY Parts Only | $16 – $363 |
| Professional Repair (Parts + Labor) | $43 – $864 |
Frequently Asked Questions
Is it safe to keep operating with fault code P0310?
Avoid prolonged operation until inspected to prevent secondary component damage.
How much does it cost to repair P0310?
DIY replacement parts average $16–$363, while professional service averages $43–$864.
Will resetting P0310 fix the problem permanently?
No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.
Related Searches & Questions
Manufacturer & Technical Reference
OBD-II Technical Reference (Ignition & Misfire System)