FaultCodes.org
P012EOBD-IIEngine Cooling & ThermostatTechnical Reference· Updated: Nov 22, 2026

P012E Fault Code: Turbocharger/Supercharger Inlet Pressure Sensor A Circuit Intermittent/Erratic

OBD-II P012E (Engine Cooling & Thermostat): Turbocharger/Supercharger Inlet Pressure Sensor A Circuit Intermittent/Erratic.

Quick AnswerHigh — Service Soon

OBD-II fault code P012E indicates Turbocharger/Supercharger Inlet Pressure Sensor A Circuit Intermittent/Erratic. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $43–$324.

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Moderate (Intermediate)
System
Engine Cooling & Thermostat
Professional Repair
$43 – $324

What This Fault Code Means

The turbocharger/supercharger inlet pressure sensor A sits ahead of the compressor – between air filter and turbocharger, or on GM's supercharged V8 between throttle and supercharger. It is an analogue 5 V pressure sensor used for the compressor pressure ratio, filter restriction and cross-checks with the other pressure sensors. P012E covers a signal that jumps or drops out briefly without staying below or above the circuit limits – typically a loose contact. Such intermittent monitors usually count short limit violations or changes faster than real pressure can move. No manufacturer document using exactly this code was found: GM handles jumps of this sensor through its range check P012B and the counting windows of P012C/P012D, and Ford's 2023 diesels report their digital sensor under P012A. The description therefore rests on CARB's circuit monitoring requirement and component information. A substitute value is used while the fault is present.

Common Symptoms

  • Check engine light on
  • Occasional power reduction or boost fluctuation
  • Often no noticeable symptoms

Most Likely Root Causes

  • Loose contact or corrosion at the sensor connector
  • Broken or chafed wire making intermittent contact
  • Sensor faulty internally (erratic output)
  • Control module or software

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P012E.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Turbocharger Inlet Pressure Sensor A.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P012E?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Turbocharger Inlet Pressure Sensor A.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Turbocharger Inlet Pressure Sensor A.
  5. 5Clear fault memory and run a verification cycle to confirm P012E does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$16 – $136
Professional Repair (Parts + Labor)$43 – $324

Frequently Asked Questions

Is it safe to keep operating with fault code P012E?

Avoid prolonged operation until inspected to prevent secondary component damage.

How much does it cost to repair P012E?

DIY replacement parts average $16–$136, while professional service averages $43–$324.

Will resetting P012E fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P012E fault code meaningP012E repair costhow to fix P012E

Manufacturer & Technical Reference

OBD-II Technical Reference (Engine Cooling & Thermostat)

Related Fault Codes

Auto & OBD-II →
P012E Fault Code: Turbocharger/Supercharger Inlet… — Fixes & Cost | FaultCodes.org