FaultCodes.org
P012DOBD-IIEngine Cooling & ThermostatTechnical Reference· Updated: Nov 22, 2026

P012D Fault Code: Turbocharger/Supercharger Inlet Pressure Sensor A Circuit High

OBD-II P012D (Engine Cooling & Thermostat): Turbocharger/Supercharger Inlet Pressure Sensor A Circuit High.

Quick AnswerHigh — Service Soon

OBD-II fault code P012D indicates Turbocharger/Supercharger Inlet Pressure Sensor A Circuit High. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $43–$324.

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Moderate (Intermediate)
System
Engine Cooling & Thermostat
Professional Repair
$43 – $324

What This Fault Code Means

The turbocharger/supercharger inlet pressure sensor A sits ahead of the compressor – between air filter and turbocharger, or on GM's supercharged V8 between throttle and supercharger. It is an analogue 5 V pressure sensor used for the compressor pressure ratio, filter restriction and cross-checks with the other pressure sensors. P012D means the signal voltage is above its upper limit – typically the signal wire shorted to the 5 V reference or battery voltage, or an open sensor ground that lets the signal rise to the reference. GM's supercharged LT4/LT5 sets it above 97 % of the reference (about 124 kPa) with 320 of 400 samples failing, monitored continuously; two trips on the LT4, one on the 2019 LT5. FCA documented false settings on the 2019 Jeep Wrangler 2.0 turbo, fixed by new engine software. The control module substitutes a modelled or ambient value and may limit boost.

Common Symptoms

  • Check engine light on
  • Reduced power or limp mode possible
  • Often no noticeable symptoms

Most Likely Root Causes

  • Signal wire shorted to 5 V reference or battery voltage
  • Sensor ground open or connector corroded
  • Sensor faulty internally
  • Control module software (false setting)

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P012D.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Turbocharger Inlet Pressure Sensor A.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P012D?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Turbocharger Inlet Pressure Sensor A.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Turbocharger Inlet Pressure Sensor A.
  5. 5Clear fault memory and run a verification cycle to confirm P012D does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$16 – $136
Professional Repair (Parts + Labor)$43 – $324

Frequently Asked Questions

Is it safe to keep operating with fault code P012D?

Avoid prolonged operation until inspected to prevent secondary component damage.

How much does it cost to repair P012D?

DIY replacement parts average $16–$136, while professional service averages $43–$324.

Will resetting P012D fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P012D fault code meaningP012D repair costhow to fix P012D

Manufacturer & Technical Reference

OBD-II Technical Reference (Engine Cooling & Thermostat)

Related Fault Codes

Auto & OBD-II →
P012D Fault Code: Turbocharger/Supercharger Inlet… — Fixes & Cost | FaultCodes.org