FaultCodes.org
P012BOBD-IIEngine Cooling & ThermostatTechnical Reference· Updated: Nov 22, 2026

P012B Fault Code: Turbocharger/Supercharger Inlet Pressure Sensor A Circuit Range/Performance

OBD-II P012B (Engine Cooling & Thermostat): Turbocharger/Supercharger Inlet Pressure Sensor A Circuit Range/Performance.

Quick AnswerHigh — Service Soon

OBD-II fault code P012B indicates Turbocharger/Supercharger Inlet Pressure Sensor A Circuit Range/Performance. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $43–$270.

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Easy (Basic Tools)
System
Engine Cooling & Thermostat
Professional Repair
$43 – $270

What This Fault Code Means

The turbocharger/supercharger inlet pressure sensor A sits between the air filter and the compressor. The engine uses it for the compressor pressure ratio, to judge air filter restriction (ambient minus inlet pressure) and to cross-check the other pressure sensors. P012B is a plausibility fault: the signal is electrically valid but stuck or offset. On GM's supercharged 6.2 V8 the sensor must read 50–115 kPa and agree within 10 kPa with MAP and ambient pressure after the engine has been off for more than 8 s; while running, it is compared with modelled values (fault above about 25–30 kPa). GM normally needs two trips, one in some 2019 applications. In operation inlet pressure is slightly below ambient because of filter losses, so a clogged filter or blocked intake lowers it further.

Common Symptoms

  • Check engine light on
  • Loss of power or boost limitation
  • Possibly no noticeable symptoms

Most Likely Root Causes

  • Sensor oiled (crankcase vent often joins before the compressor) or drifted
  • Air filter heavily clogged or intake blocked or collapsed
  • Leak in the intake pipe between filter and compressor or at the sensor flange
  • High resistance in the wiring
  • Comparison sensor (MAP, baro, MAF) wrong or software

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P012B.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Turbocharger Inlet Pressure Sensor A.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P012B?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Turbocharger Inlet Pressure Sensor A.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Turbocharger Inlet Pressure Sensor A.
  5. 5Clear fault memory and run a verification cycle to confirm P012B does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$16 – $113
Professional Repair (Parts + Labor)$43 – $270

Frequently Asked Questions

Is it safe to keep operating with fault code P012B?

Avoid prolonged operation until inspected to prevent secondary component damage.

How much does it cost to repair P012B?

DIY replacement parts average $16–$113, while professional service averages $43–$270.

Will resetting P012B fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P012B fault code meaningP012B repair costhow to fix P012B

Manufacturer & Technical Reference

OBD-II Technical Reference (Engine Cooling & Thermostat)

Related Fault Codes

Auto & OBD-II →
P012B Fault Code: Turbocharger/Supercharger Inlet… — Fixes & Cost | FaultCodes.org