FaultCodes.org
P0127OBD-IIEngine Cooling & ThermostatTechnical Reference· Updated: Nov 22, 2026

P0127 Fault Code: Intake Air Temperature Too High

OBD-II P0127 (Engine Cooling & Thermostat): Intake Air Temperature Too High.

Quick AnswerHigh — Service Soon

OBD-II fault code P0127 indicates Intake Air Temperature Too High. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $54–$1296.

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Moderate (Intermediate)
System
Engine Cooling & Thermostat
Professional Repair
$54 – $1,296

What This Fault Code Means

P0127 is not a circuit fault but a functional check of the air path: the measured intake air temperature is too high for the operating state. The logic is documented for a Bosch EDC16 diesel (Saab 9-3): if the intake air exceeds 130 °C and does not fall below it within 45 s after the exhaust gas recirculation valve is closed, hot exhaust gas is evidently still entering or the sensor is wrong. The engine then disables EGR and runs in limp mode with reduced torque. GM has the code in its diesel software but disabled for US OBD II; Ford reports an overly hot intake air reading as P0111 instead. On other engines a hot reading can also come from warm under-bonnet air being drawn in.

Common Symptoms

  • Check engine light on
  • Loss of power, limp mode with torque limit
  • EGR switched off
  • Knock tendency and retarded ignition on petrol engines

Most Likely Root Causes

  • EGR valve stuck open or not sealing (diesel)
  • EGR cooler clogged or bypass flap stuck in bypass
  • Charge air cooler dirty or airflow through it blocked
  • Sensor reading wrong, or hot engine-bay air drawn in (loose intake duct)

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0127.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Intake Air Temperature Sensor.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0127?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Intake Air Temperature Sensor.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Intake Air Temperature Sensor.
  5. 5Clear fault memory and run a verification cycle to confirm P0127 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$19 – $544
Professional Repair (Parts + Labor)$54 – $1,296

Frequently Asked Questions

Is it safe to keep operating with fault code P0127?

Avoid prolonged operation until inspected to prevent secondary component damage.

How much does it cost to repair P0127?

DIY replacement parts average $19–$544, while professional service averages $54–$1296.

Will resetting P0127 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0127 fault code meaningP0127 repair costhow to fix P0127

Manufacturer & Technical Reference

OBD-II Technical Reference (Engine Cooling & Thermostat)

Related Fault Codes

Auto & OBD-II →
P0127 Fault Code: Intake Air Temperature Too High — Fixes & Cost | FaultCodes.org