FaultCodes.org
P0122OBD-IIEngine Cooling & ThermostatTechnical Reference· Updated: Nov 22, 2026

P0122 Fault Code: Throttle/Pedal Position Sensor/Switch A Circuit Low

OBD-II P0122 (Engine Cooling & Thermostat): Throttle/Pedal Position Sensor/Switch A Circuit Low.

Quick AnswerHigh — Service Soon

OBD-II fault code P0122 indicates Throttle/Pedal Position Sensor/Switch A Circuit Low. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $43–$486.

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Moderate (Intermediate)
System
Engine Cooling & Thermostat
Professional Repair
$43 – $486

What This Fault Code Means

Sensor A is, in practice, throttle position sensor 1 at the throttle body; the accelerator pedal has its own codes (P2120 onwards). With a cable-operated throttle there is a single potentiometer (about 0.5 V closed to 4.5 V wide open). Electronic throttles have two sensors sharing a 5 V reference and ground, usually running in opposite directions – on GM throttle sensor 1 falls from 3–4 V at idle to below 1 V at full throttle. P0122 means the signal voltage of sensor A is below its lower limit – electrically meant, not 'throttle closed': typically an open or grounded signal wire or a missing 5 V reference. Limits: Ford below 0.25 V (detected within 1 s), Saab/GM 2011 below 0.3 V for 1 s, Saab cable system below 0.2 V for 5 s. GM treats it as a one-trip fault and switches to reduced engine power; Ford lights the MIL and wrench lamp and continues on the remaining sensor or in limp mode.

Common Symptoms

  • Check engine light, on electronic throttles also wrench lamp
  • Limp mode with reduced power ('Reduced Engine Power') on electronic throttles
  • Engine barely responds to the pedal or stalls at idle
  • High idle, A/C switched off (cable systems)

Most Likely Root Causes

  • Signal wire open or shorted to ground
  • Connector at the throttle body loose or corroded
  • 5 V reference missing (open, or shorted by another sensor)
  • Sensor or throttle body faulty
  • Engine control module faulty

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0122.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Throttle Position Sensor.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0122?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Throttle Position Sensor.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Throttle Position Sensor.
  5. 5Clear fault memory and run a verification cycle to confirm P0122 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$16 – $204
Professional Repair (Parts + Labor)$43 – $486

Frequently Asked Questions

Is it safe to keep operating with fault code P0122?

Avoid prolonged operation until inspected to prevent secondary component damage.

How much does it cost to repair P0122?

DIY replacement parts average $16–$204, while professional service averages $43–$486.

Will resetting P0122 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0122 fault code meaningP0122 repair costhow to fix P0122

Manufacturer & Technical Reference

OBD-II Technical Reference (Engine Cooling & Thermostat)

Related Fault Codes

Auto & OBD-II →
P0122 Fault Code: Throttle/Pedal Position… — Fixes & Cost | FaultCodes.org