FaultCodes.org
P0120OBD-IIEngine Cooling & ThermostatTechnical Reference· Updated: Nov 22, 2026

P0120 Fault Code: Throttle/Pedal Position Sensor/Switch A Circuit

OBD-II P0120 (Engine Cooling & Thermostat): Throttle/Pedal Position Sensor/Switch A Circuit.

Quick AnswerHigh — Service Soon

OBD-II fault code P0120 indicates Throttle/Pedal Position Sensor/Switch A Circuit. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $43–$486.

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Moderate (Intermediate)
System
Engine Cooling & Thermostat
Professional Repair
$43 – $486

What This Fault Code Means

Sensor A is, in practice, throttle position sensor 1 at the throttle body; the accelerator pedal has its own codes (P2120 onwards). With a cable-operated throttle there is a single potentiometer (about 0.5 V closed to 4.5 V wide open). Electronic throttles have two sensors sharing a 5 V reference and ground, usually running in opposite directions – on GM throttle sensor 1 falls from 3–4 V at idle to below 1 V at full throttle. P0120 is the general circuit fault, used when the fault cannot be classed as low or high or when the sensor is digital. Ford sets it on digital SENT throttle sensors when the sensor reports an error for more than 4 s, together with the MIL and wrench lamp; Saab Trionic used it as a collective code. GM and Ford's analogue throttles report P0122/P0123 instead. Electronic throttles then fall back to a spring-loaded limp position with limited power.

Common Symptoms

  • Check engine light, on electronic throttles also wrench lamp
  • Limp mode with reduced power ('Reduced Engine Power') on electronic throttles
  • Raised or unsteady idle (cable systems)
  • Poor throttle response, jerky driving

Most Likely Root Causes

  • Connector at the throttle body corroded or loose, broken wire
  • Sensor or throttle body with integrated sensor faulty
  • 5 V reference disturbed (short on another sensor of the same circuit)
  • Engine control module faulty

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0120.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Throttle Position Sensor.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0120?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Throttle Position Sensor.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Throttle Position Sensor.
  5. 5Clear fault memory and run a verification cycle to confirm P0120 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$16 – $204
Professional Repair (Parts + Labor)$43 – $486

Frequently Asked Questions

Is it safe to keep operating with fault code P0120?

Avoid prolonged operation until inspected to prevent secondary component damage.

How much does it cost to repair P0120?

DIY replacement parts average $16–$204, while professional service averages $43–$486.

Will resetting P0120 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0120 fault code meaningP0120 repair costhow to fix P0120

Manufacturer & Technical Reference

OBD-II Technical Reference (Engine Cooling & Thermostat)

Related Fault Codes

Auto & OBD-II →
P0120 Fault Code: Throttle/Pedal Position Sensor/Switch A Circuit | FaultCodes.org