FaultCodes.org
P0112OBD-IIEngine Cooling & ThermostatTechnical Reference· Updated: Nov 22, 2026

P0112 Fault Code: Intake Air Temperature Sensor 1 Circuit Low Bank 1

OBD-II P0112 (Engine Cooling & Thermostat): Intake Air Temperature Sensor 1 Circuit Low Bank 1.

Quick AnswerHigh — Service Soon

OBD-II fault code P0112 indicates Intake Air Temperature Sensor 1 Circuit Low Bank 1. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $43–$270.

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Easy (Basic Tools)
System
Engine Cooling & Thermostat
Professional Repair
$43 – $270

What This Fault Code Means

Intake air temperature sensor 1 is the first air temperature sensor in the intake path; depending on the vehicle it is built into the mass air flow sensor, mounted near the air filter or, on some naturally aspirated GM engines, fitted in the intake manifold. Most versions are NTC thermistors in a 5 V divider: the hotter the air, the lower the signal voltage. P0112 means the signal is below its valid range. With an NTC sensor that points to a short to ground in the signal wire or an internally shorted sensor, and the control module would read an implausibly hot value (GM about 150 °C). Documented limits: Ford petrol below 0.244 V for 5 s, Ford diesel below 0.10 V, GM below 62 ohms. The circuit is monitored continuously; GM needs two trips. Some systems then use the coolant temperature, capped at 40 °C, as a substitute and limit torque.

Common Symptoms

  • Check engine light on
  • Usually hardly noticeable
  • Retarded ignition, reduced power or torque limit on some systems
  • Harder cold start possible

Most Likely Root Causes

  • Signal wire shorted to ground (chafed insulation)
  • Sensor shorted internally
  • Moisture or corrosion in the connector
  • Engine control module faulty

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0112.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Intake Air Temperature Sensor.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0112?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Intake Air Temperature Sensor.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Intake Air Temperature Sensor.
  5. 5Clear fault memory and run a verification cycle to confirm P0112 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$16 – $113
Professional Repair (Parts + Labor)$43 – $270

Frequently Asked Questions

Is it safe to keep operating with fault code P0112?

Avoid prolonged operation until inspected to prevent secondary component damage.

How much does it cost to repair P0112?

DIY replacement parts average $16–$113, while professional service averages $43–$270.

Will resetting P0112 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0112 fault code meaningP0112 repair costhow to fix P0112

Manufacturer & Technical Reference

OBD-II Technical Reference (Engine Cooling & Thermostat)

Related Fault Codes

Auto & OBD-II →
P0112 Fault Code: Intake Air Temperature Sensor 1 Circuit Low Bank 1 | FaultCodes.org