FaultCodes.org
P0111OBD-IIEngine Cooling & ThermostatTechnical Reference· Updated: Nov 22, 2026

P0111 Fault Code: Intake Air Temperature Sensor 1 Circuit Range/Performance Bank 1

OBD-II P0111 (Engine Cooling & Thermostat): Intake Air Temperature Sensor 1 Circuit Range/Performance Bank 1.

Quick AnswerHigh — Service Soon

OBD-II fault code P0111 indicates Intake Air Temperature Sensor 1 Circuit Range/Performance Bank 1. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $43–$324.

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Easy (Basic Tools)
System
Engine Cooling & Thermostat
Professional Repair
$43 – $324

What This Fault Code Means

Intake air temperature sensor 1 is the first air temperature sensor in the intake path; depending on the vehicle it is built into the mass air flow sensor, mounted near the air filter or, on some naturally aspirated GM engines, fitted in the intake manifold. Most versions are NTC thermistors in a 5 V divider: the hotter the air, the lower the signal voltage. P0111 is a plausibility fault: the signal is electrically valid but does not fit. The usual test runs at key-on after a long soak (Ford 6 h, GM 8 h): the intake air sensor is compared with other temperature sensors such as coolant, cylinder head, charge air cooler or IAT2, which should all read about the same. GM flags it above about 25 °C deviation, Ford above about 17 °C; Ford first confirms with a drive above 40 mph because sunshine can warm a sensor, and also sets P0111 if the air reads over 66 °C while driving. A detected block heater suspends the test. Two consecutive trips are needed.

Common Symptoms

  • Check engine light on
  • Usually no noticeable symptoms
  • Slightly changed idle, power or cold start possible
  • Code often returns only after an overnight soak

Most Likely Root Causes

  • Sensor drifting or stuck at one value (ageing, oil from crankcase ventilation)
  • Contact resistance at connector or wiring distorts the reading
  • Comparison sensor (coolant, IAT2, charge air cooler) wrong
  • Undetected preheater, heat soak or sensor mounted near a heat source

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0111.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Intake Air Temperature Sensor.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0111?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Intake Air Temperature Sensor.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Intake Air Temperature Sensor.
  5. 5Clear fault memory and run a verification cycle to confirm P0111 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$16 – $136
Professional Repair (Parts + Labor)$43 – $324

Frequently Asked Questions

Is it safe to keep operating with fault code P0111?

Avoid prolonged operation until inspected to prevent secondary component damage.

How much does it cost to repair P0111?

DIY replacement parts average $16–$136, while professional service averages $43–$324.

Will resetting P0111 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0111 fault code meaningP0111 repair costhow to fix P0111

Manufacturer & Technical Reference

OBD-II Technical Reference (Engine Cooling & Thermostat)

Related Fault Codes

Auto & OBD-II →
P0111 Fault Code: Intake Air Temperature Sensor 1… — Fixes & Cost | FaultCodes.org