FaultCodes.org
P0110OBD-IIEngine Cooling & ThermostatTechnical Reference· Updated: Nov 22, 2026

P0110 Fault Code: Intake Air Temperature Sensor 1 Circuit Bank 1

OBD-II P0110 (Engine Cooling & Thermostat): Intake Air Temperature Sensor 1 Circuit Bank 1.

Quick AnswerHigh — Service Soon

OBD-II fault code P0110 indicates Intake Air Temperature Sensor 1 Circuit Bank 1. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $43–$324.

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Easy (Basic Tools)
System
Engine Cooling & Thermostat
Professional Repair
$43 – $324

What This Fault Code Means

Intake air temperature sensor 1 is the first air temperature sensor in the intake path; depending on the vehicle it is built into the mass air flow sensor, mounted near the air filter or, on some naturally aspirated GM engines, fitted in the intake manifold. Most versions are NTC thermistors in a 5 V divider: the hotter the air, the lower the signal voltage. P0110 is the general circuit fault. With a conventional analogue sensor most manufacturers report low and high signals separately (P0112/P0113), so P0110 mainly appears in two cases: with digital (SENT) sensors that combine air mass and temperature, where it stands for lost communication or an implausible status (Ford diesel 2023, after about 5 s), and in some Bosch systems as a collective code whose fault type byte tells open circuit from short to ground. The control module then uses a substitute temperature; some systems also limit torque.

Common Symptoms

  • Check engine light on
  • Reduced power or torque limitation on some systems
  • Otherwise usually inconspicuous; cold start may be slightly worse

Most Likely Root Causes

  • Connector or wiring to the sensor open or corroded
  • Sensor or mass air flow sensor with built-in temperature sensor faulty
  • Sensor supply or ground disturbed
  • Engine control module faulty

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0110.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Intake Air Temperature Sensor.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0110?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Intake Air Temperature Sensor.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Intake Air Temperature Sensor.
  5. 5Clear fault memory and run a verification cycle to confirm P0110 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$16 – $136
Professional Repair (Parts + Labor)$43 – $324

Frequently Asked Questions

Is it safe to keep operating with fault code P0110?

Avoid prolonged operation until inspected to prevent secondary component damage.

How much does it cost to repair P0110?

DIY replacement parts average $16–$136, while professional service averages $43–$324.

Will resetting P0110 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0110 fault code meaningP0110 repair costhow to fix P0110

Manufacturer & Technical Reference

OBD-II Technical Reference (Engine Cooling & Thermostat)

Related Fault Codes

Auto & OBD-II →
P0110 Fault Code: Intake Air Temperature Sensor 1 Circuit Bank 1 | FaultCodes.org