FaultCodes.org
P0024OBD-IIPowertrain & Engine ManagementTechnical Reference· Updated: Nov 22, 2026

P0024 Fault Code: "B" Camshaft Position - Timing Over-Advanced or System Performance (Bank 2)

OBD-II P0024 (Powertrain & Engine Management): "B" Camshaft Position - Timing Over-Advanced or System Performance (Bank 2).

Quick AnswerHigh — Service Soon

OBD-II fault code P0024 indicates "B" Camshaft Position - Timing Over-Advanced or System Performance (Bank 2). Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $65–$1944.

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Moderate (Intermediate)
System
Powertrain & Engine Management
Professional Repair
$65 – $1,944

What This Fault Code Means

The engine control module compares the commanded position of the exhaust camshaft on bank 2 with the actual position it calculates from the camshaft and crankshaft sensors. This code is set when the camshaft sits further advanced than commanded for longer than a calibrated time, or, depending on the manufacturer, when the target is missed in either direction ("system performance"). Typical cause is a phaser that does not return to its rest position, for example because the oil control valve sticks open or its screen is clogged. Bank 2 exists only on V and boxer engines; it is the cylinder bank without cylinder 1.

Common Symptoms

  • Check engine light on
  • Rough idle and hesitation
  • Engine may stall at idle
  • Rattling from the timing drive at cold start
  • Higher fuel consumption

Most Likely Root Causes

  • Oil level too low, oil sludged or wrong viscosity
  • Screen at the oil control valve clogged with debris
  • Oil control valve mechanically sticking
  • Cam phaser worn or its locking pin sticking
  • Timing chain worn or fitted incorrectly after a repair

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0024.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Cam Phaser Exhaust Bank2.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0024?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Cam Phaser Exhaust Bank2.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Cam Phaser Exhaust Bank2.
  5. 5Clear fault memory and run a verification cycle to confirm P0024 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$23 – $816
Professional Repair (Parts + Labor)$65 – $1,944

Frequently Asked Questions

Is it safe to keep operating with fault code P0024?

Avoid prolonged operation until inspected to prevent secondary component damage.

How much does it cost to repair P0024?

DIY replacement parts average $23–$816, while professional service averages $65–$1944.

Will resetting P0024 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0024 fault code meaningP0024 repair costhow to fix P0024

Manufacturer & Technical Reference

OBD-II Technical Reference (Powertrain & Engine Management)

Related Fault Codes

Auto & OBD-II →
P0024 Fault Code: "B" Camshaft Position - Timing… — Fixes & Cost | FaultCodes.org