FaultCodes.org
P0017OBD-IIPowertrain & Engine ManagementVerified Guide· Updated: Nov 22, 2026

OBD-II P0017: Crankshaft Position – Camshaft Position Correlation (Bank 1 Sensor B)

Mechanical timing phase mismatch between crankshaft (CKP) and Bank 1 exhaust ("B") camshaft (CMP)—STOP aggressive driving on interference engines (valve-to-piston risk); check oil level/sludge & exhaust VVT OCV (6–12 Ω) first, then diagnose stretched timing chain, slipped exhaust phaser/tone wheel, or failed tensioner via oscilloscope.

Quick AnswerCritical — Stop Immediately

Code P0017 (SAE J2012) warns of a mechanical phase correlation misalignment between the crankshaft (`CKP`) and the Bank 1 Exhaust (`"B"`) camshaft (`CMP`)—meaning their physical timing marks shifted relative to each other. CRITICAL WARNING: STOP driving aggressively (or shut down immediately if metallic chain rattle is heard)—most modern DOHC engines are interference designs, where a skipped timing chain or belt causes catastrophic valve-to-piston collision! Always check engine oil level/sludge and the exhaust VVT OCV solenoid (`6.0–12.0 Ω`) FIRST (a sludge-jammed OCV or low oil pressure can pin the exhaust phaser off-phase); if oil and OCV check out, have a professional verify a stretched timing chain, failed hydraulic chain tensioner, or slipped exhaust cam phaser / reluctor tone wheel via dual-channel CKP+CMP oscilloscope waveform comparison ($40–$220 oil/OCV check; $650–$2,400 professional timing chain/phaser repair).

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Professional Recommended
System
Powertrain & Engine Management
Professional Repair
$650 – $2,400

What This Fault Code Means

At every engine revolution, the ECM compares Crankshaft Position (CKP) teeth against the Bank 1 Exhaust Camshaft (CMP "B") pulse edge. Even with VVT parked at base lock-pin zero, if timing chain wear elongates slack, a hydraulic tensioner loses oil prime, or a press-fit exhaust camshaft reluctor ring / cam phaser slips out of mechanical alignment by roughly ~8°–15° (often 1 chain tooth), the ECM throws P0017—sometimes alongside intake correlation P0016.

Common Symptoms

  • Check Engine Light (P0017, sometimes paired with P0016 or P0014) and extended cold cranking / hard start
  • Loud metallic timing chain slap or cold-start rattle from the front cover for 2–5 seconds on startup
  • Severe loss of low-end power, rough idle, exhaust backfiring, or engine shutoff if timing skips multiple teeth

Most Likely Root Causes

  • Stretched primary timing chain, broken plastic chain guides, or collapsed hydraulic chain tensioner (#1 mechanical cause)
  • Low, neglected, or sludged engine oil starving the hydraulic tensioner & jamming the Bank 1 exhaust VVT OCV / cam phaser lock pin
  • Slipped exhaust camshaft phaser vane/hub or spun press-fit camshaft reluctor tone wheel
  • Improperly timed recent timing belt/chain replacement (off by 1 tooth) or failing CKP/CMP sensor dropout

Technical Thresholds & Specifications

Parameter / ConditionFactory Spec / Threshold
SAE J2012 Mechanical Correlation Fault

Indicates mechanical tooth/phase offset beyond ~8°–15° tolerance

Crankshaft (CKP) vs Bank 1 Exhaust Cam ("B" CMP)
Interference Engine Risk

Jumped timing chain/belt causes severe valve-to-piston impact damage

STOP aggressive driving immediately
Quick First-Line Electrical/Oil Check

Rule out starved VVT hydraulic locking before removing timing cover

Oil level/sludge & Exhaust OCV (6.0–12.0 Ω)
Definitive Non-Invasive Proof

Confirms stretched chain, bad tensioner, or slipped tone wheel instantly

Dual-channel CKP + CMP oscilloscope overlay

Commonly Affected Models & Service Bulletins

  • GM 3.6L Alloytec / HFV6 & 2.4L Ecotec Engines (stretched timing chains & slipped tone wheels)
  • Mercedes-Benz M272/M273/M271 & BMW N20/N47/N55 Engines (timing chain, balance shaft & exhaust phaser)
  • Hyundai / Kia / Ford / Volkswagen / Audi DOHC Interference Engines (SAE J2012)

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Check engine oil level and dipstick for dark sludge or metallic glitter immediately—low oil or thick sludge starves timing tensioners and jams exhaust VVT OCVs before mechanical failure occurs.
  2. 2Test the Bank 1 Exhaust (`"B"`) VVT OCV solenoid (6.0–12.0 Ω @ 20 °C, OL to housing, clean mesh filter screen, crisp 12V bench click) and scan whether P0016 (intake) or P0014 co-occurs.
  3. 3Have a qualified technician connect a 2-channel oscilloscope across `CKP` and Bank 1 Exhaust `CMP "B"` against a factory known-good waveform (identifying exact tooth offset without tearing down the timing cover), plus mechanically verify TDC alignment marks if correlation fails.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are engine oil critically low/sludged OR is the Bank 1 exhaust VVT OCV outside 6.0–12.0 Ω / jammed with debris—with zero chain rattle?

Step-by-Step Troubleshooting & Fix

Tools & Parts Reference

2-channel automotive oscilloscope (for live CKP vs Exhaust CMP correlation overlay)Digital multimeter (6.0–12.0 Ω exhaust VVT OCV check) & OBD-II scan toolOEM camshaft/crankshaft locking timing tool kit & torque wrench (professional repair)
  1. 1If oil is severely low or sludged with zero metallic rattle, immediately perform an oil & OEM filter change and clean/replace any stuck exhaust VVT OCV (`6.0–12.0 Ω`) before condemning the chain.
  2. 2If CKP/CMP oscilloscope traces confirm mechanical phase shift or cold chain slap persists, tow or drive gently straight to service—do NOT rev high on interference engines!
  3. 3Replace the complete timing chain kit (primary & secondary chains, hydraulic tensioners, nylon guides, and worn sprockets) plus any failed exhaust cam phaser (using exact OEM cam-locking fixtures).
  4. 4If an oscilloscope shows a slipped exhaust camshaft reluctor tone wheel (seen on some GM/VW/Mercedes engines), replace the camshaft/phaser assembly, perform Crankshaft Variation Relearn, and verify zero correlation offset.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$40 – $220
Professional Repair (Parts + Labor)$650 – $2,400

Certified Technician Service Checklist

This fault involves sealed safety, gas, or high-voltage systems. Share these details when requesting a repair quote.

  • Share exact brand & fault code: P0017 (Powertrain & Engine Management)
  • Record appliance/boiler serial, model plate, or pressure reading before calling
  • Typical certified technician range: $650 – $2,400

Frequently Asked Questions

Can I keep driving my car with OBD-II code P0017?

No—especially never rev or drive aggressively! On interference engines, P0017 often signals a stretched timing chain or failing tensioner that is one startup or hard acceleration away from jumping multiple teeth and smashing pistons into valves.

What is the difference between P0017 and P0016?

Both are mechanical Crankshaft-to-Camshaft correlation faults on Bank 1: `P0016` flags Bank 1 Sensor "A" (Intake camshaft), whereas `P0017` flags Bank 1 Sensor "B" (Exhaust camshaft)—seeing both together strongly points to a stretched primary timing chain or worn tensioner.

Related Searches & Questions

OBD2 P0017 crankshaft camshaft correlation bank 1 sensor Bis P0017 safe to drive timing chain valve damageP0016 and P0017 together stretched timing chainP0017 exhaust cam phaser vs VVT solenoid cost

Verified Official & Engineering References

Plain Text / AI View

Related Fault Codes

Auto & OBD-II →
OBD-II P0017: Crankshaft Position – Camshaft… — Fixes & Cost | FaultCodes.org