# OBD-II P0017: OBD-II P0017: Crankshaft Position – Camshaft Position Correlation (Bank 1 Sensor B)

> **Quick Answer:** Code **P0017** (SAE J2012) warns of a **mechanical phase correlation misalignment between the crankshaft (`CKP`) and the Bank 1 Exhaust (`"B"`) camshaft (`CMP`)**—meaning their physical timing marks shifted relative to each other. **CRITICAL WARNING: STOP driving aggressively (or shut down immediately if metallic chain rattle is heard)**—most modern DOHC engines are **interference designs**, where a skipped timing chain or belt causes **catastrophic valve-to-piston collision**! Always check **engine oil level/sludge** and the **exhaust VVT OCV solenoid (`6.0–12.0 Ω`)** FIRST (a sludge-jammed OCV or low oil pressure can pin the exhaust phaser off-phase); if oil and OCV check out, have a professional verify a **stretched timing chain, failed hydraulic chain tensioner, or slipped exhaust cam phaser / reluctor tone wheel** via dual-channel **CKP+CMP oscilloscope waveform comparison** ($40–$220 oil/OCV check; $650–$2,400 professional timing chain/phaser repair).

- **URL:** https://faultcodes.org/automotive/obd2-p0017
- **Category:** Automotive & OBD-II
- **Brand / Standard:** OBD-II
- **System Area:** Powertrain & Engine Management
- **Severity:** Critical — Stop Immediately
- **Safe to Operate?:** No — Risk of Damage
- **DIY Difficulty:** Professional Recommended
- **Updated:** 2026-11-22T00:00:00Z

## What This Fault Code Means
At every engine revolution, the ECM compares Crankshaft Position (`CKP`) teeth against the Bank 1 Exhaust Camshaft (`CMP "B"`) pulse edge. Even with VVT parked at base lock-pin zero, if timing chain wear elongates slack, a hydraulic tensioner loses oil prime, or a press-fit exhaust camshaft reluctor ring / cam phaser slips out of mechanical alignment by roughly `~8°–15°` (often 1 chain tooth), the ECM throws `P0017`—sometimes alongside intake correlation `P0016`.

## Technical Thresholds & Specifications
| Parameter / Condition | Factory Spec / Threshold | Note |
| --- | --- | --- |
| SAE J2012 Mechanical Correlation Fault | Crankshaft (CKP) vs Bank 1 Exhaust Cam ("B" CMP) | Indicates mechanical tooth/phase offset beyond ~8°–15° tolerance |
| Interference Engine Risk | STOP aggressive driving immediately | Jumped timing chain/belt causes severe valve-to-piston impact damage |
| Quick First-Line Electrical/Oil Check | Oil level/sludge & Exhaust OCV (6.0–12.0 Ω) | Rule out starved VVT hydraulic locking before removing timing cover |
| Definitive Non-Invasive Proof | Dual-channel CKP + CMP oscilloscope overlay | Confirms stretched chain, bad tensioner, or slipped tone wheel instantly |

## Commonly Affected Models & Service Bulletins
- GM 3.6L Alloytec / HFV6 & 2.4L Ecotec Engines (stretched timing chains & slipped tone wheels)
- Mercedes-Benz M272/M273/M271 & BMW N20/N47/N55 Engines (timing chain, balance shaft & exhaust phaser)
- Hyundai / Kia / Ford / Volkswagen / Audi DOHC Interference Engines (SAE J2012)

## Common Symptoms
- Check Engine Light (`P0017`, sometimes paired with `P0016` or `P0014`) and extended cold cranking / hard start
- Loud metallic **timing chain slap or cold-start rattle** from the front cover for 2–5 seconds on startup
- Severe loss of low-end power, rough idle, exhaust backfiring, or engine shutoff if timing skips multiple teeth

## Most Likely Root Causes
- **Stretched primary timing chain, broken plastic chain guides, or collapsed hydraulic chain tensioner** (#1 mechanical cause)
- **Low, neglected, or sludged engine oil** starving the hydraulic tensioner & jamming the **Bank 1 exhaust VVT OCV / cam phaser lock pin**
- **Slipped exhaust camshaft phaser vane/hub** or **spun press-fit camshaft reluctor tone wheel**
- Improperly timed recent timing belt/chain replacement (off by 1 tooth) or failing `CKP`/`CMP` sensor dropout

## Tools & Parts Reference
- 2-channel automotive oscilloscope (for live `CKP` vs Exhaust `CMP` correlation overlay)
- Digital multimeter (`6.0–12.0 Ω` exhaust VVT OCV check) & OBD-II scan tool
- OEM camshaft/crankshaft locking timing tool kit & torque wrench (professional repair)

## Step-by-Step Troubleshooting & Fix
1. If oil is severely low or sludged with zero metallic rattle, immediately perform an oil & OEM filter change and clean/replace any stuck **exhaust VVT OCV (`6.0–12.0 Ω`)** before condemning the chain.
2. If `CKP`/`CMP` oscilloscope traces confirm mechanical phase shift or cold chain slap persists, **tow or drive gently straight to service**—do NOT rev high on interference engines!
3. Replace the complete **timing chain kit (primary & secondary chains, hydraulic tensioners, nylon guides, and worn sprockets)** plus any failed **exhaust cam phaser** (using exact OEM cam-locking fixtures).
4. If an oscilloscope shows a **slipped exhaust camshaft reluctor tone wheel** (seen on some GM/VW/Mercedes engines), replace the camshaft/phaser assembly, perform **Crankshaft Variation Relearn**, and verify zero correlation offset.

## Estimated Repair Cost Benchmark
| Currency | DIY Parts Only | Professional Repair (Parts + Labor) |
| --- | --- | --- |
| USD | $40–$220 | $650–$2400 |
| GBP | £32–£175 | £500–£1850 |
| CAD | CA$55–CA$290 | CA$850–CA$3100 |
| EUR | €38–€200 | €580–€2150 |
| CHF | CHF 45–CHF 240 | CHF 780–CHF 2750 |

## Frequently Asked Questions
### Can I keep driving my car with OBD-II code P0017?
No—especially **never rev or drive aggressively**! On interference engines, `P0017` often signals a stretched timing chain or failing tensioner that is one startup or hard acceleration away from jumping multiple teeth and **smashing pistons into valves**.

### What is the difference between P0017 and P0016?
Both are mechanical Crankshaft-to-Camshaft correlation faults on Bank 1: **`P0016`** flags Bank 1 **Sensor "A" (Intake camshaft)**, whereas **`P0017`** flags Bank 1 **Sensor "B" (Exhaust camshaft)**—seeing both together strongly points to a stretched primary timing chain or worn tensioner.


## Verified Official & Engineering References
- [US EPA On-Board Diagnostics (OBD) Standards](https://www.epa.gov/obd) (Regulation / Standard)
- [SAE International: SAE J2012 Diagnostic Trouble Code Standards](https://www.sae.org/standards/content/j2012/) (Regulation / Standard)
- [NHTSA Vehicle Safety & Emissions Recalls / TSB Portal](https://www.nhtsa.gov/recalls) (Official Support)
