FaultCodes.org
P0010OBD-IIPowertrain & Engine ManagementVerified Guide· Updated: Nov 22, 2026

OBD-II P0010: "A" Camshaft Position Actuator Circuit / Open (Bank 1)

Pure electrical open or short in the Bank 1 intake ("A") VVT Oil Control Valve (OCV) solenoid circuit—ohm-test the unplugged coil (6.0–12.0 Ω @ 20 °C, OL to housing ground), check oil-wicked connectors & 12 V fuse, and confirm PCM PWM ground pulse before replacing the OCV.

Quick AnswerModerate — Plan Repair

Code P0010 (SAE J2012) is a pure electrical circuit fault (open coil, broken wire, or short) on the Bank 1 Intake (`"A"`) Variable Valve Timing (`VVT`) Oil Control Valve (`OCV`) solenoid—unlike mechanical timing/sludge code P0011! Because the intake OCV mounts conveniently near the top front of the Bank 1 cylinder head, testing takes 5 minutes: unplug the 2-wire intake OCV and measure coil resistance (`6.0–12.0 Ω` @ `20 °C` healthy, `OL` from either pin to metal housing ground); also inspect the plug for wicked engine oil, verify the `12 V` ignition supply fuse, and check the PCM PWM ground pulse with a small test light or scope before ordering a new solenoid ($30–$95 DIY; $150–$340 shop).

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Easy (Basic Tools)
System
Powertrain & Engine Management
Professional Repair
$150 – $340

What This Fault Code Means

The PCM controls intake camshaft phase by pulsing a ~150–300 Hz PWM ground signal to the 2-pin Bank 1 Intake VVT OCV solenoid while supplying fused 12 V ignition power. During key-on and running checks, the PCM driver monitors circuit continuity and inductive flyback; if the internal coil opens from heat/vibration (OL), oil wicks into the plug causing corrosion, a 12 V fuse blows, or a wiring harness chafes open, P0010 sets immediately.

Common Symptoms

  • Illuminated Check Engine Light (P0010)—sometimes triggered instantly KOEO before engine start
  • Mild drop in low-end torque, fuel economy, or slightly rough idle because intake VVT defaults to locked zero-advance
  • Visible engine oil seeping inside the 2-pin intake OCV harness connector

Most Likely Root Causes

  • Internally open (`OL`) or shorted (`< 3 Ω`) Bank 1 intake (`"A"`) VVT Oil Control Valve (`OCV`) solenoid coil (#1 cause)
  • Engine oil wicking through a failing OCV seal into the 2-pin connector, causing terminal corrosion or poor pin contact
  • Chafed, brittle, or rodent-chewed 2-wire OCV harness pigtail or backed-out terminal pin
  • Blown ECM / Engine Controls `12 V` fuse (shared across coils/actuators) or failed PCM PWM driver

Technical Thresholds & Specifications

Parameter / ConditionFactory Spec / Threshold
SAE J2012 Fault Classification

Open coil, short, oil-fouled plug, or missing 12 V / PWM pulse

Pure Electrical Circuit Fault (Intake "A" Bank 1)
OCV Solenoid Coil Resistance

Measured unplugged; OL or continuity to housing condemns solenoid

6.0–12.0 Ω @ 20 °C (OL to solenoid housing)
Control Signal Architecture

Verify PCM ground pulse with a low-wattage test light / scope

Fused 12 V Ignition Feed + PCM PWM Ground
Common Physical Clue

Leaking internal seal ruins electrical contact and sets P0010

Engine oil wicking into 2-pin OCV plug

Commonly Affected Models & Service Bulletins

  • Chevrolet / GMC / Opel Ecotec 2.0L / 2.2L / 2.4L (10-minute top-access intake VVT OCV)
  • Toyota Camry / Corolla / RAV4 & Honda / Hyundai / Kia 4-Cylinder & V6 VVT Systems
  • Ford / Nissan / Volkswagen / BMW Intake Camshaft OCV Actuators (SAE J2012)

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Confirm which actuator is Bank 1 Intake (`"A"`): Bank 1 is the cylinder #1 side, and intake "A" sits on the intake-manifold camshaft side—do NOT swap the exhaust "B" solenoid (P0013) by mistake!
  2. 2Unplug the 2-pin intake OCV connector, inspect inside for engine oil wicking or bent female pins, and measure solenoid coil resistance (`6.0–12.0 Ω` @ `20 °C`) plus pin-to-solenoid-body isolation (OL required).
  3. 3On the vehicle harness plug KOEO, test one pin for `12 V` ignition supply (check underhood VVT/ECM fuses if absent) and check the second pin's continuity back to the PCM—or clip a 194-bulb / LED test light across both harness pins while commanding VVT duty cycle to verify crisp PCM PWM pulsing.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Does the unplugged Bank 1 intake OCV coil measure OL (open), < 3 Ω (shorted), outside 6.0–12.0 Ω (@ 20 °C), OR leak oil out of its connector pins?

Step-by-Step Troubleshooting & Fix

Tools & Parts Reference

Digital multimeter (6.0–12.0 Ω coil test, OL housing check, 12 V feed & continuity)Low-wattage 194 test light / oscilloscope & OBD-II bi-directional scanner (PWM verify)10 mm socket & electrical contact cleaner
  1. 1If 12 V ignition supply is absent, inspect and replace any blown VVT/ECM fuse and trace shorted wiring.
  2. 2Clean any oil-soaked 2-pin connector thoroughly with electrical contact spray and replace splayed or cracked pigtail connectors.
  3. 3If the unplugged intake OCV reads OL, < 3 Ω, fails 6.0–12.0 Ω, shorts to its housing, or shows oil leaking out of its plastic electrical socket, remove the single retaining bolt (usually 10 mm) and install a new OEM Bank 1 intake VVT OCV solenoid with lightly oiled O-ring.
  4. 4Clear P0010 and verify live Desired vs Actual Intake Cam Angle tracks cleanly during a road test.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$30 – $95
Professional Repair (Parts + Labor)$150 – $340

Recommended Diagnostic Tools & Replacement Parts

Check OEM specifications and compatible tools for this repair.

Frequently Asked Questions

What is the difference between P0010 and P0011?

Both refer to the Bank 1 intake ("A") camshaft, but `P0010` is an electrical circuit fault (open OCV coil, blown fuse, or broken wire), whereas `P0011` is a mechanical/oil timing fault (cam over-advanced from dirty oil, sludge, or phaser wear).

Can I clean a P0010 VVT solenoid instead of replacing it?

No—cleaning only helps mechanical sludge codes (P0011/P0014). P0010 means the electrical copper coil inside the OCV or its wiring failed (OL or short), so cleaning cannot restore a broken winding.

Related Searches & Questions

OBD2 P0010 intake camshaft actuator circuit fixP0010 VVT OCV solenoid ohm test 6 to 12 ohmsP0010 vs P0011 difference electrical vs mechanicalP0010 location bank 1 intake replacement cost

Verified Official & Engineering References

Plain Text / AI View

Related Fault Codes

Auto & OBD-II →
OBD-II P0010: "A" Camshaft Position Actuator Circuit / Open (Bank 1) | FaultCodes.org