# OBD-II P0010: OBD-II P0010: "A" Camshaft Position Actuator Circuit / Open (Bank 1)

> **Quick Answer:** Code **P0010** (SAE J2012) is a **pure electrical circuit fault** (open coil, broken wire, or short) on the **Bank 1 Intake (`"A"`) Variable Valve Timing (`VVT`) Oil Control Valve (`OCV`) solenoid**—unlike mechanical timing/sludge code `P0011`! Because the intake OCV mounts conveniently near the top front of the Bank 1 cylinder head, testing takes 5 minutes: unplug the 2-wire intake OCV and measure coil resistance (**`6.0–12.0 Ω` @ `20 °C`** healthy, **`OL` from either pin to metal housing ground**); also inspect the plug for **wicked engine oil**, verify the **`12 V` ignition supply fuse**, and check the **PCM PWM ground pulse** with a small test light or scope before ordering a new solenoid ($30–$95 DIY; $150–$340 shop).

- **URL:** https://faultcodes.org/automotive/obd2-p0010
- **Category:** Automotive & OBD-II
- **Brand / Standard:** OBD-II
- **System Area:** Powertrain & Engine Management
- **Severity:** Moderate — Plan Repair
- **Safe to Operate?:** Yes (Short Term)
- **DIY Difficulty:** Easy (Basic Tools)
- **Updated:** 2026-11-22T00:00:00Z

## What This Fault Code Means
The PCM controls intake camshaft phase by pulsing a `~150–300 Hz` PWM ground signal to the 2-pin **Bank 1 Intake VVT OCV solenoid** while supplying fused `12 V` ignition power. During key-on and running checks, the PCM driver monitors circuit continuity and inductive flyback; if the internal coil opens from heat/vibration (`OL`), oil wicks into the plug causing corrosion, a `12 V` fuse blows, or a wiring harness chafes open, `P0010` sets immediately.

## Technical Thresholds & Specifications
| Parameter / Condition | Factory Spec / Threshold | Note |
| --- | --- | --- |
| SAE J2012 Fault Classification | Pure Electrical Circuit Fault (Intake "A" Bank 1) | Open coil, short, oil-fouled plug, or missing 12 V / PWM pulse |
| OCV Solenoid Coil Resistance | 6.0–12.0 Ω @ 20 °C (OL to solenoid housing) | Measured unplugged; OL or continuity to housing condemns solenoid |
| Control Signal Architecture | Fused 12 V Ignition Feed + PCM PWM Ground | Verify PCM ground pulse with a low-wattage test light / scope |
| Common Physical Clue | Engine oil wicking into 2-pin OCV plug | Leaking internal seal ruins electrical contact and sets P0010 |

## Commonly Affected Models & Service Bulletins
- Chevrolet / GMC / Opel Ecotec 2.0L / 2.2L / 2.4L (10-minute top-access intake VVT OCV)
- Toyota Camry / Corolla / RAV4 & Honda / Hyundai / Kia 4-Cylinder & V6 VVT Systems
- Ford / Nissan / Volkswagen / BMW Intake Camshaft OCV Actuators (SAE J2012)

## Common Symptoms
- Illuminated Check Engine Light (`P0010`)—sometimes triggered instantly KOEO before engine start
- Mild drop in low-end torque, fuel economy, or slightly rough idle because intake VVT defaults to locked zero-advance
- Visible engine oil seeping inside the 2-pin intake OCV harness connector

## Most Likely Root Causes
- **Internally open (`OL`) or shorted (`< 3 Ω`) Bank 1 intake (`"A"`) VVT Oil Control Valve (`OCV`) solenoid coil** (#1 cause)
- **Engine oil wicking through a failing OCV seal into the 2-pin connector**, causing terminal corrosion or poor pin contact
- Chafed, brittle, or rodent-chewed 2-wire OCV harness pigtail or backed-out terminal pin
- Blown **ECM / Engine Controls `12 V` fuse** (shared across coils/actuators) or failed PCM PWM driver

## Tools & Parts Reference
- Digital multimeter (`6.0–12.0 Ω` coil test, `OL` housing check, `12 V` feed & continuity)
- Low-wattage 194 test light / oscilloscope & OBD-II bi-directional scanner (PWM verify)
- 10 mm socket & electrical contact cleaner

## Step-by-Step Troubleshooting & Fix
1. If `12 V` ignition supply is absent, inspect and replace any blown VVT/ECM fuse and trace shorted wiring.
2. Clean any oil-soaked 2-pin connector thoroughly with electrical contact spray and replace splayed or cracked pigtail connectors.
3. If the unplugged intake OCV reads `OL`, `< 3 Ω`, fails `6.0–12.0 Ω`, shorts to its housing, or shows oil leaking out of its plastic electrical socket, remove the single retaining bolt (usually `10 mm`) and install a **new OEM Bank 1 intake VVT OCV solenoid** with lightly oiled O-ring.
4. Clear `P0010` and verify live Desired vs Actual Intake Cam Angle tracks cleanly during a road test.

## Estimated Repair Cost Benchmark
| Currency | DIY Parts Only | Professional Repair (Parts + Labor) |
| --- | --- | --- |
| USD | $30–$95 | $150–$340 |
| GBP | £25–£78 | £120–£265 |
| CAD | CA$40–CA$125 | CA$195–CA$445 |
| EUR | €28–€85 | €135–€310 |
| CHF | CHF 35–CHF 105 | CHF 175–CHF 385 |

## Frequently Asked Questions
### What is the difference between P0010 and P0011?
Both refer to the Bank 1 intake (`"A"`) camshaft, but **`P0010` is an electrical circuit fault** (open OCV coil, blown fuse, or broken wire), whereas **`P0011` is a mechanical/oil timing fault** (cam over-advanced from dirty oil, sludge, or phaser wear).

### Can I clean a P0010 VVT solenoid instead of replacing it?
No—cleaning only helps mechanical sludge codes (`P0011`/`P0014`). `P0010` means the electrical copper coil inside the OCV or its wiring failed (`OL` or short), so cleaning cannot restore a broken winding.


## Verified Official & Engineering References
- [US EPA On-Board Diagnostics (OBD) Standards](https://www.epa.gov/obd) (Regulation / Standard)
- [SAE International: SAE J2012 Diagnostic Trouble Code Standards](https://www.sae.org/standards/content/j2012/) (Regulation / Standard)
- [NHTSA Vehicle Safety & Emissions Recalls / TSB Portal](https://www.nhtsa.gov/recalls) (Official Support)
