FaultCodes.org
B0014OBD-IIBody Control, Airbag & ComfortTechnical Reference· Updated: Nov 22, 2026

B0014 Fault Code: Driver Knee Airbag Deployment Control

OBD-II B0014 (Body Control, Airbag & Comfort): Driver Knee Airbag Deployment Control.

Quick AnswerModerate — Plan Repair

OBD-II fault code B0014 indicates Driver Knee Airbag Deployment Control. Usually safe for short trips if no severe drivability or safety warnings are active. Typical professional repair costs $86–$972.

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Professional Recommended
System
Body Control, Airbag & Comfort
Professional Repair
$86 – $972

What This Fault Code Means

B0014 is not in the public J2012 code lists; there the driver knee airbag has B0004 and the passenger knee airbag B0013. The number is documented only at General Motors, and with another meaning. GM modules from about 2010 use B0014 for the side airbag in the driver seat; the Saab 9-4X 2011 manual adds a fault byte for each failure, from a shorted or open loop to a high reading (0D, over 4.2 ohms) or a low one (0E, under 1.4 ohms). GM bulletins blame chafed or loose seat harness connectors and high connector resistance on Silverado and Tahoe 2014-15, Equinox, Traverse and the Bolt EV. Older Saab 9-3 modules used B0014 for a short in the passenger frontal stage 2 loop. A knee airbag meaning for this code is not publicly documented.

Common Symptoms

  • Airbag warning lamp or service airbag message, often intermittent
  • Affected airbag may not deploy
  • Safety note: do not probe the airbag circuit yourself; unplug airbag connectors only with the battery disconnected and the stated wait time observed

Most Likely Root Causes

  • On GM vehicles loose or high-resistance side airbag connector under or in the driver seat
  • Seat harness chafed by seat frame, motor or foam
  • Internal fault in the airbag module served by this loop

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside B0014.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Knee Airbag Module.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside B0014?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Knee Airbag Module.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Knee Airbag Module.
  5. 5Clear fault memory and run a verification cycle to confirm B0014 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$30 – $408
Professional Repair (Parts + Labor)$86 – $972

Certified Technician Service Checklist

This fault involves sealed safety, gas, or high-voltage systems. Share these details when requesting a repair quote.

  • Share exact brand & fault code: B0014 (Body Control, Airbag & Comfort)
  • Record appliance/boiler serial, model plate, or pressure reading before calling
  • Typical certified technician range: $86 – $972

Frequently Asked Questions

Is it safe to keep operating with fault code B0014?

Usually safe for short trips if no severe drivability or safety warnings are active.

How much does it cost to repair B0014?

DIY replacement parts average $30–$408, while professional service averages $86–$972.

Will resetting B0014 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

B0014 fault code meaningB0014 repair costhow to fix B0014

Manufacturer & Technical Reference

OBD-II Technical Reference (Body Control, Airbag & Comfort)

Related Fault Codes

Auto & OBD-II →
B0014 Fault Code: Driver Knee Airbag Deployment Control | FaultCodes.org