B0012 Fault Code: Passenger Frontal Stage 3 Deployment Control
OBD-II B0012 (Body Control, Airbag & Comfort): Passenger Frontal Stage 3 Deployment Control.
OBD-II fault code B0012 indicates Passenger Frontal Stage 3 Deployment Control. Usually safe for short trips if no severe drivability or safety warnings are active. Typical professional repair costs $108–$1404.
- Safe to Operate?
- Yes (Short Term)
- DIY Difficulty
- Professional Recommended
- System
- Body Control, Airbag & Comfort
- Professional Repair
- $108 – $1,404
What This Fault Code Means
In the J2012 order B0012 is the third element of the front passenger airbag. Mercedes-Benz uses B001213 for the squib of the vent valve in that airbag, and Mitsubishi lists B0012 as passenger airbag module 3. GM gives the number a different meaning. Its later sensing and diagnostic modules assign B0012 to stage 1 of the steering wheel airbag; the Saab 9-4X 2011 manual trips it after two seconds of contact with supply or ground, an open, more than 4.4 ohms or less than 1.7 ohms; GM bulletins link it to chafed coil wires on the 2009 Cobalt and to weak terminal tension at the coil connector on the 2015 CTS. Older Saab 9-3 modules used B0012 for low resistance in the passenger stage 2 loop. Read the code with the maker's tool before choosing which airbag to check.
Common Symptoms
- Airbag warning lamp on
- Depending on maker, passenger airbag venting or GM driver airbag stage 1 affected
- Safety note: do not probe the airbag circuit yourself; unplug airbag connectors only with the battery disconnected and the stated wait time observed
Most Likely Root Causes
- Open or shorted third squib (vent valve) in the passenger airbag (J2012 meaning)
- On GM vehicles weak terminal tension or chafed wires at the steering wheel airbag coil
- Restraint control module fault
Diagnostic Checks Before Replacing Parts
Verify the exact faulty component before ordering replacements.
- 1Read stored freeze-frame data and companion codes alongside B0012.
- 2Inspect electrical connectors, fuses, and harnesses connected to Passenger Airbag Module.
- 3Verify live sensor telemetry before ordering replacement components.
Interactive Symptom Triage
Answer 3 quick checks to narrow down the faulty component before spending money on parts.
Are any companion fault codes stored alongside B0012?
Step-by-Step Troubleshooting & Fix
- 1Scan for companion fault codes and address upstream circuit issues first.
- 2Visually inspect wiring harnesses, plugs, and hoses around Passenger Airbag Module.
- 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
- 4Repair damaged wiring or install an OEM-grade replacement Passenger Airbag Module.
- 5Clear fault memory and run a verification cycle to confirm B0012 does not return.
Estimated Repair Cost Benchmark
Typical DIY parts and certified technician labor ranges. Select a currency below.
| Repair Path | USD |
|---|---|
| DIY Parts Only | $38 – $590 |
| Professional Repair (Parts + Labor) | $108 – $1,404 |
Certified Technician Service Checklist
This fault involves sealed safety, gas, or high-voltage systems. Share these details when requesting a repair quote.
- Share exact brand & fault code: B0012 (Body Control, Airbag & Comfort)
- Record appliance/boiler serial, model plate, or pressure reading before calling
- Typical certified technician range: $108 – $1,404
Frequently Asked Questions
Is it safe to keep operating with fault code B0012?
Usually safe for short trips if no severe drivability or safety warnings are active.
How much does it cost to repair B0012?
DIY replacement parts average $38–$590, while professional service averages $108–$1404.
Will resetting B0012 fix the problem permanently?
No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.
Related Searches & Questions
Manufacturer & Technical Reference
OBD-II Technical Reference (Body Control, Airbag & Comfort)