FaultCodes.org
P0719OBD-IITransmission & DrivetrainTechnical Reference· Updated: Nov 22, 2026

P0719 Fault Code: Brake Switch B Circuit Low

OBD-II P0719 (Transmission & Drivetrain): Brake Switch B Circuit Low.

Quick AnswerHigh — Service Soon

OBD-II fault code P0719 indicates Brake Switch B Circuit Low. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $43–$162.

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Easy (Basic Tools)
System
Transmission & Drivetrain
Professional Repair
$43 – $162

What This Fault Code Means

Brake switch B is the brake signal to the transmission module or a second brake switch channel, used to release the converter clutch, adapt shift strategy on grades and cancel cruise control. Low and high describe the signal voltage, and what that means depends on polarity: GM's converter clutch brake switch is closed at rest (12 V), while Saab's Trionic 8 sees 12 V when braking. Detection is always a plausibility check against driving: the brake reads applied during accelerations or never applied during decelerations. P0719 means the signal stays low. For GM that reads as brake applied: 2006 transmission modules flag it after eight accelerations without the brake releasing, without MIL. Saab's Trionic 8 flags the brake light signal not changing during four decelerations from 40 to 3 km/h and disables cruise control. The opposite is P0724.

Common Symptoms

  • Cruise control cannot be activated or switches off
  • Unusual shifting, converter clutch behaviour changed
  • No downshift on uphill grades (Subaru)
  • Brake lights stay off or on

Most Likely Root Causes

  • Brake light switch faulty or misadjusted
  • Wire to the module open (GM) or shorted to ground (Saab T8)
  • Connector at the pedal box corroded
  • Brake light circuit fuse blown

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0719.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Brake Switch.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0719?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Brake Switch.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Brake Switch.
  5. 5Clear fault memory and run a verification cycle to confirm P0719 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$16 – $68
Professional Repair (Parts + Labor)$43 – $162

Frequently Asked Questions

Is it safe to keep operating with fault code P0719?

Avoid prolonged operation until inspected to prevent secondary component damage.

How much does it cost to repair P0719?

DIY replacement parts average $16–$68, while professional service averages $43–$162.

Will resetting P0719 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0719 fault code meaningP0719 repair costhow to fix P0719

Manufacturer & Technical Reference

OBD-II Technical Reference (Transmission & Drivetrain)

Related Fault Codes

Auto & OBD-II →
P0719 Fault Code: Brake Switch B Circuit Low — Causes, Fixes & Cost | FaultCodes.org