FaultCodes.org
P0497OBD-IIEVAP Emissions ControlTechnical Reference· Updated: Nov 22, 2026

P0497 Fault Code: EVAP System Low Purge Flow

OBD-II P0497 (EVAP Emissions Control): EVAP System Low Purge Flow.

Quick AnswerLow — Minor Issue

OBD-II fault code P0497 indicates EVAP System Low Purge Flow. Usually safe for short trips if no severe drivability or safety warnings are active. Typical professional repair costs $54–$486.

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Moderate (Intermediate)
System
EVAP Emissions Control
Professional Repair
$54 – $486

What This Fault Code Means

The evaporative emission (EVAP) system stores fuel vapour from the tank in a charcoal canister; a purge valve lets the engine draw it off, and a vent valve opens the canister to fresh air. P0497 is the counterpart of P0496: the module purges but sees too little or no purge flow, judged indirectly from fuel trim, idle control or tank vacuum – CARB requires missing purge flow to be detected. Code-specific use is documented only by Land Rover (5.0-litre V8) and in a GM fault group for systems with a sealed tank (Volt, ELR); standard GM and Ford systems use other codes, such as P0455. The canister is then not purged and saturates.

Common Symptoms

  • Check engine light on
  • Fuel smell around the car
  • Fuel nozzle clicks off early

Most Likely Root Causes

  • Purge valve stuck closed, does not open
  • Purge line off, kinked or blocked (check valve sticking)
  • Canister or vent filter blocked (e.g. after overfilling)
  • Vent valve stuck closed

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0497.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Evap Purge Valve.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0497?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Evap Purge Valve.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Evap Purge Valve.
  5. 5Clear fault memory and run a verification cycle to confirm P0497 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$19 – $204
Professional Repair (Parts + Labor)$54 – $486

Frequently Asked Questions

Is it safe to keep operating with fault code P0497?

Usually safe for short trips if no severe drivability or safety warnings are active.

How much does it cost to repair P0497?

DIY replacement parts average $19–$204, while professional service averages $54–$486.

Will resetting P0497 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0497 fault code meaningP0497 repair costhow to fix P0497

Manufacturer & Technical Reference

OBD-II Technical Reference (EVAP Emissions Control)

Related Fault Codes

Auto & OBD-II →
P0497 Fault Code: EVAP System Low Purge Flow — Causes, Fixes & Cost | FaultCodes.org