FaultCodes.org
P0458OBD-IIEVAP Emissions ControlTechnical Reference· Updated: Nov 22, 2026

P0458 Fault Code: EVAP System Purge Control Valve A Circuit Low

OBD-II P0458 (EVAP Emissions Control): EVAP System Purge Control Valve A Circuit Low.

Quick AnswerLow — Minor Issue

OBD-II fault code P0458 indicates EVAP System Purge Control Valve A Circuit Low. Usually safe for short trips if no severe drivability or safety warnings are active. Typical professional repair costs $43–$216.

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Easy (Basic Tools)
System
EVAP Emissions Control
Professional Repair
$43 – $216

What This Fault Code Means

The evaporative emission (EVAP) system stores fuel vapour from the tank in a charcoal canister; a purge valve lets the engine draw it off, and a vent valve opens the canister to fresh air. Purge valve A is switched to ground by the module and fed from the main relay. P0458 means its control wire is shorted to ground: GM detects it with the driver off, when the line sits at ground instead of supply (20 of 25 samples, MIL after two trips); Saab's ME9 uses below 2.6 V at the output. The valve is then energised and open all the time, purging is uncontrolled – rough idle, rich mixture or hard starting after refuelling are possible.

Common Symptoms

  • Check engine light on
  • Rough idle or rich mixture possible (valve permanently open)
  • Starting problems after refuelling possible

Most Likely Root Causes

  • Purge valve control wire chafed against ground
  • Purge valve coil shorted internally
  • Connector scorched or wet
  • Driver in the engine module

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0458.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Evap Purge Valve.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0458?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Evap Purge Valve.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Evap Purge Valve.
  5. 5Clear fault memory and run a verification cycle to confirm P0458 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$16 – $91
Professional Repair (Parts + Labor)$43 – $216

Frequently Asked Questions

Is it safe to keep operating with fault code P0458?

Usually safe for short trips if no severe drivability or safety warnings are active.

How much does it cost to repair P0458?

DIY replacement parts average $16–$91, while professional service averages $43–$216.

Will resetting P0458 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0458 fault code meaningP0458 repair costhow to fix P0458

Manufacturer & Technical Reference

OBD-II Technical Reference (EVAP Emissions Control)

Related Fault Codes

Auto & OBD-II →
P0458 Fault Code: EVAP System Purge Control Valve A Circuit Low | FaultCodes.org