FaultCodes.org
P0447OBD-IIEVAP Emissions ControlTechnical Reference· Updated: Nov 22, 2026

P0447 Fault Code: EVAP System Vent Control Circuit Open

OBD-II P0447 (EVAP Emissions Control): EVAP System Vent Control Circuit Open.

Quick AnswerLow — Minor Issue

OBD-II fault code P0447 indicates EVAP System Vent Control Circuit Open. Usually safe for short trips if no severe drivability or safety warnings are active. Typical professional repair costs $43–$270.

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Easy (Basic Tools)
System
EVAP Emissions Control
Professional Repair
$43 – $270

What This Fault Code Means

The evaporative emission (EVAP) system stores fuel vapour from the tank in a charcoal canister; a purge valve lets the engine draw it off, and a vent valve opens the canister to fresh air. P0447 belongs to the older scheme for the vent valve circuit (P0446 circuit, P0447 open, P0448 shorted), used by Subaru (also in the Saab 9-2X), VW and Nissan; GM reports an open vent circuit as P0449, Ford as P0446. On Subaru the valve is fed from the main relay and switched to ground by the module; if the voltage at the module output is missing or the coil is high-resistance (nominal 10–100 Ω), the code sets after two consecutive drives. The valve stays in its rest position and the leak test cannot run.

Common Symptoms

  • Check engine light on
  • EVAP leak test does not run, readiness not set
  • Usually no change in driving

Most Likely Root Causes

  • Vent valve connector corroded or off (underbody, splash water)
  • Vent valve coil open (resistance outside 10–100 Ω)
  • Wire to the module or supply from the main relay open
  • Engine module or its connector

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0447.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Evap Vent Valve.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0447?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Evap Vent Valve.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Evap Vent Valve.
  5. 5Clear fault memory and run a verification cycle to confirm P0447 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$16 – $113
Professional Repair (Parts + Labor)$43 – $270

Frequently Asked Questions

Is it safe to keep operating with fault code P0447?

Usually safe for short trips if no severe drivability or safety warnings are active.

How much does it cost to repair P0447?

DIY replacement parts average $16–$113, while professional service averages $43–$270.

Will resetting P0447 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0447 fault code meaningP0447 repair costhow to fix P0447

Manufacturer & Technical Reference

OBD-II Technical Reference (EVAP Emissions Control)

Related Fault Codes

Auto & OBD-II →
P0447 Fault Code: EVAP System Vent Control Circuit Open | FaultCodes.org