FaultCodes.org
P0438OBD-IICatalytic & Exhaust EmissionsTechnical Reference· Updated: Nov 22, 2026

P0438 Fault Code: Catalyst Temperature Sensor Circuit High Bank 2 Sensor 1

OBD-II P0438 (Catalytic & Exhaust Emissions): Catalyst Temperature Sensor Circuit High Bank 2 Sensor 1.

Quick AnswerModerate — Plan Repair

OBD-II fault code P0438 indicates Catalyst Temperature Sensor Circuit High Bank 2 Sensor 1. Usually safe for short trips if no severe drivability or safety warnings are active. Typical professional repair costs $65–$324.

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Moderate (Intermediate)
System
Catalytic & Exhaust Emissions
Professional Repair
$65 – $324

What This Fault Code Means

Some engines – mainly diesels – measure the temperature at or in the catalyst with a thermistor in a voltage divider instead of only modelling it; most makers report exhaust temperature sensors under P0544 ff, P2031 ff or P2080 ff instead. Sensor 1 of bank 2 is the first catalyst temperature sensor on the side without cylinder 1. P0438 means the signal voltage is above its upper limit – typically the sensor or its wiring is open, or the signal is shorted to positive. No manufacturer document available to us uses this code; the description follows CARB, which requires input circuits to be checked for circuit faults and plausibility, and the comparable exhaust temperature sensors.

Common Symptoms

  • Check engine light on
  • Usually no noticeable change (substitute value from the model)
  • Diesel: filter regeneration distorted or blocked, possibly further codes such as P2459 or P0420

Most Likely Root Causes

  • Sensor or wire open (broken by vibration or heat)
  • Connector off or loose, ground wire open
  • Signal wire shorted to positive
  • Engine module

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0438.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Catalyst Temperature Sensor B2S1.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0438?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Catalyst Temperature Sensor B2S1.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Catalyst Temperature Sensor B2S1.
  5. 5Clear fault memory and run a verification cycle to confirm P0438 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$23 – $136
Professional Repair (Parts + Labor)$65 – $324

Frequently Asked Questions

Is it safe to keep operating with fault code P0438?

Usually safe for short trips if no severe drivability or safety warnings are active.

How much does it cost to repair P0438?

DIY replacement parts average $23–$136, while professional service averages $65–$324.

Will resetting P0438 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0438 fault code meaningP0438 repair costhow to fix P0438

Manufacturer & Technical Reference

OBD-II Technical Reference (Catalytic & Exhaust Emissions)

Related Fault Codes

Auto & OBD-II →
P0438 Fault Code: Catalyst Temperature Sensor… — Fixes & Cost | FaultCodes.org