FaultCodes.org
P0427OBD-IICatalytic & Exhaust EmissionsTechnical Reference· Updated: Nov 22, 2026

P0427 Fault Code: Catalyst Temperature Sensor Circuit Low Bank 1 Sensor 1

OBD-II P0427 (Catalytic & Exhaust Emissions): Catalyst Temperature Sensor Circuit Low Bank 1 Sensor 1.

Quick AnswerModerate — Plan Repair

OBD-II fault code P0427 indicates Catalyst Temperature Sensor Circuit Low Bank 1 Sensor 1. Usually safe for short trips if no severe drivability or safety warnings are active. Typical professional repair costs $65–$324.

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Moderate (Intermediate)
System
Catalytic & Exhaust Emissions
Professional Repair
$65 – $324

What This Fault Code Means

Some engines – mainly diesels – measure the temperature at or in the catalyst with a thermistor in a voltage divider instead of only modelling it; most makers report exhaust temperature sensors under P0544 ff, P2031 ff or P2080 ff instead. Sensor 1 of bank 1 is the first catalyst temperature sensor on the side with cylinder 1. P0427 means the signal voltage is below its lower limit – typically the signal wire is shorted to ground or the sensor is shorted internally. FCA's 3.0-litre EcoDiesel uses this sensor (middle of the oxidation catalyst and particulate filter unit), but no document available to us names this particular code.

Common Symptoms

  • Check engine light on
  • Usually no noticeable change (substitute value from the model)
  • Diesel: filter regeneration distorted or blocked, possibly further codes such as P2459 or P0420

Most Likely Root Causes

  • Signal wire shorted to ground (chafed)
  • Sensor shorted internally
  • Water or corrosion in the connector
  • Engine module

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0427.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Catalyst Temperature Sensor B1S1.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0427?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Catalyst Temperature Sensor B1S1.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Catalyst Temperature Sensor B1S1.
  5. 5Clear fault memory and run a verification cycle to confirm P0427 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$23 – $136
Professional Repair (Parts + Labor)$65 – $324

Frequently Asked Questions

Is it safe to keep operating with fault code P0427?

Usually safe for short trips if no severe drivability or safety warnings are active.

How much does it cost to repair P0427?

DIY replacement parts average $23–$136, while professional service averages $65–$324.

Will resetting P0427 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0427 fault code meaningP0427 repair costhow to fix P0427

Manufacturer & Technical Reference

OBD-II Technical Reference (Catalytic & Exhaust Emissions)

Related Fault Codes

Auto & OBD-II →
P0427 Fault Code: Catalyst Temperature Sensor… — Fixes & Cost | FaultCodes.org