FaultCodes.org
P0327OBD-IIIgnition & Misfire SystemTechnical Reference· Updated: Nov 22, 2026

P0327 Fault Code: Knock/Combustion Vibration Sensor A Circuit Low

OBD-II P0327 (Ignition & Misfire System): Knock/Combustion Vibration Sensor A Circuit Low.

Quick AnswerHigh — Service Soon

OBD-II fault code P0327 indicates Knock/Combustion Vibration Sensor A Circuit Low. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $43–$648.

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Moderate (Intermediate)
System
Ignition & Misfire System
Professional Repair
$43 – $648

What This Fault Code Means

The knock sensor is a piezoelectric structure-borne sound sensor bolted to the engine block; the module evaluates its signal per cylinder and retards ignition when it detects knock. Sensor A is the first sensor (bank 1 or a single sensor). With a fault the module retards ignition across the board as protection – noticeable loss of power and higher consumption. P0327 means the diagnostic DC voltage at the sensor input is too low – the signal or return wire is shorted to ground. GM biases each input through a resistor network and sets the code below 8 % of 5 V in 50 of 63 samples, in the first trip; Ford checks actively once every 250 engine cycles on modules with this circuit. Subaru introduced a more durable sensor for this fault.

Common Symptoms

  • Check engine light on
  • Loss of power, sluggish response from ignition retard
  • Higher fuel consumption

Most Likely Root Causes

  • Signal or return wire chafed to ground
  • Moisture or corrosion in connector or sensor
  • Sensor faulty internally (series issue on some models)
  • Engine module internal

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0327.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Knock Sensor A.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0327?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Knock Sensor A.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Knock Sensor A.
  5. 5Clear fault memory and run a verification cycle to confirm P0327 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$16 – $272
Professional Repair (Parts + Labor)$43 – $648

Frequently Asked Questions

Is it safe to keep operating with fault code P0327?

Avoid prolonged operation until inspected to prevent secondary component damage.

How much does it cost to repair P0327?

DIY replacement parts average $16–$272, while professional service averages $43–$648.

Will resetting P0327 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0327 fault code meaningP0327 repair costhow to fix P0327

Manufacturer & Technical Reference

OBD-II Technical Reference (Ignition & Misfire System)

Related Fault Codes

Auto & OBD-II →
P0327 Fault Code: Knock/Combustion Vibration Sensor A Circuit Low | FaultCodes.org