FaultCodes.org
P030AOBD-IIIgnition & Misfire SystemTechnical Reference· Updated: Nov 22, 2026

P030A Fault Code: Ignition A Control Signal Circuit/Open

OBD-II P030A (Ignition & Misfire System): Ignition A Control Signal Circuit/Open.

Quick AnswerHigh — Service Soon

OBD-II fault code P030A indicates Ignition A Control Signal Circuit/Open. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $54–$540.

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Moderate (Intermediate)
System
Ignition & Misfire System
Professional Repair
$54 – $540

What This Fault Code Means

Ignition A is one of the control signal lines from the engine module to an ignition module, ignition output stage or group of coils; which cylinders it serves is defined by the manufacturer, not by the code standard. The code concerns the logic-level control signal, not the coil's primary current (that has its own codes, P0351 ff and P2300 ff). P030A means the control line is open – the module sees a voltage with its driver off that indicates high resistance. No manufacturer using these codes was found; GM reports coil control faults as P0351 ff (open above 30 kΩ, first trip), so the description follows CARB and that analogy. The affected coils fire wrongly or not at all, causing misfire; many modules then shut off injection to those cylinders to protect the catalyst.

Common Symptoms

  • Check engine light on
  • Misfire, jerking, rough idle
  • Loss of power, possibly cylinders shut off
  • Additional misfire codes P0300 ff

Most Likely Root Causes

  • Control line or connector pin open (corrosion, pushed-back pin)
  • Ignition module or coil with integrated driver of this group faulty
  • Supply or ground of the ignition module faulty
  • Driver stage in the engine module

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P030A.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Ignition Control A.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P030A?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Ignition Control A.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Ignition Control A.
  5. 5Clear fault memory and run a verification cycle to confirm P030A does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$19 – $227
Professional Repair (Parts + Labor)$54 – $540

Frequently Asked Questions

Is it safe to keep operating with fault code P030A?

Avoid prolonged operation until inspected to prevent secondary component damage.

How much does it cost to repair P030A?

DIY replacement parts average $19–$227, while professional service averages $54–$540.

Will resetting P030A fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P030A fault code meaningP030A repair costhow to fix P030A

Manufacturer & Technical Reference

OBD-II Technical Reference (Ignition & Misfire System)

Related Fault Codes

Auto & OBD-II →
P030A Fault Code: Ignition A Control Signal Circuit/Open | FaultCodes.org