FaultCodes.org
P0309OBD-IIIgnition & Misfire SystemTechnical Reference· Updated: Nov 22, 2026

P0309 Fault Code: Cylinder 9 Misfire Detected

OBD-II P0309 (Ignition & Misfire System): Cylinder 9 Misfire Detected.

Quick AnswerHigh — Service Soon

OBD-II fault code P0309 indicates Cylinder 9 Misfire Detected. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $43–$864.

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Easy (Basic Tools)
System
Ignition & Misfire System
Professional Repair
$43 – $864

What This Fault Code Means

The engine module detects misfire from crankshaft speed: a cylinder that does not fire gives no acceleration impulse. At a catalyst-damaging rate (CARB: at least 5 % per 200 revolutions) the warning light flashes; at an emissions-relevant rate (at least 1 % per 1,000 revolutions – GM about 2–5 %, Ford 0.9–1.5 %) it comes on after two trips. Ford and GM may shut off a misfiring cylinder's injector to protect the catalyst. P0309 means more than 90 % of the detected misfires fall on cylinder 9. Usual causes are the ignition coil or spark plug of that cylinder, its injector, or low compression; a quick test is to swap coil or plug with a neighbouring cylinder and see whether the misfire moves. Cylinder 9 exists on ten-cylinder engines such as Ford's 6.8 litre V10; there an under-torqued crankshaft pulley bolt and engine software caused false misfire codes on all cylinders.

Common Symptoms

  • Check engine light on, flashing at a catalyst-damaging rate
  • Rough idle, jerking, vibration
  • Loss of power, hesitation
  • Smell of unburnt fuel, higher consumption

Most Likely Root Causes

  • Ignition coil of cylinder 9 faulty (coil, connector, ground)
  • Spark plug of cylinder 9 worn, sooted, cracked or wrongly gapped
  • Injector of cylinder 9 clogged or leaking, or its control
  • Low compression on cylinder 9 (valve, rings, head gasket) or local false air
  • Water or oil in the plug well

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0309.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Ignition Coil Cylinder 9.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0309?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Ignition Coil Cylinder 9.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Ignition Coil Cylinder 9.
  5. 5Clear fault memory and run a verification cycle to confirm P0309 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$16 – $363
Professional Repair (Parts + Labor)$43 – $864

Frequently Asked Questions

Is it safe to keep operating with fault code P0309?

Avoid prolonged operation until inspected to prevent secondary component damage.

How much does it cost to repair P0309?

DIY replacement parts average $16–$363, while professional service averages $43–$864.

Will resetting P0309 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0309 fault code meaningP0309 repair costhow to fix P0309

Manufacturer & Technical Reference

OBD-II Technical Reference (Ignition & Misfire System)

Related Fault Codes

Auto & OBD-II →
P0309 Fault Code: Cylinder 9 Misfire Detected — Causes, Fixes & Cost | FaultCodes.org