FaultCodes.org
P0125OBD-IIEngine Cooling & ThermostatTechnical Reference· Updated: Nov 22, 2026

P0125 Fault Code: Insufficient Coolant Temperature for Closed Loop Fuel Control

OBD-II P0125 (Engine Cooling & Thermostat): Insufficient Coolant Temperature for Closed Loop Fuel Control.

Quick AnswerHigh — Service Soon

OBD-II fault code P0125 indicates Insufficient Coolant Temperature for Closed Loop Fuel Control. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $43–$378.

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Moderate (Intermediate)
System
Engine Cooling & Thermostat
Professional Repair
$43 – $378

What This Fault Code Means

Closed-loop mixture control using the oxygen sensors is only released once the coolant has reached a minimum temperature. CARB requires that this happens within set times – from 2006 two minutes if the engine starts up to 8 °C below the release temperature, five minutes if 8–19 °C below. P0125 means it took too long. Ford checks once per cold start and fails if coolant is still below 10 °C while its model already expects over 27 °C; Mitsubishi expects about 7 °C within 90–300 s and also fails if coolant drops back below 40 °C. Long idling suspends the test. Usual causes are a thermostat stuck open or a sensor reading too cold. GM does not use this code in the tables checked.

Common Symptoms

  • Check engine light on
  • Engine warms up slowly, heater stays cold for a long time
  • Higher consumption during warm-up
  • Temperature gauge reads low

Most Likely Root Causes

  • Thermostat stuck open (especially in cold weather)
  • Coolant sensor reading too cold or slow (drift, contact resistance)
  • Low coolant level or air at the sensor
  • Much idling or coasting in frost
  • Engine control module

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0125.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Thermostat.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0125?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Thermostat.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Thermostat.
  5. 5Clear fault memory and run a verification cycle to confirm P0125 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$16 – $159
Professional Repair (Parts + Labor)$43 – $378

Frequently Asked Questions

Is it safe to keep operating with fault code P0125?

Avoid prolonged operation until inspected to prevent secondary component damage.

How much does it cost to repair P0125?

DIY replacement parts average $16–$159, while professional service averages $43–$378.

Will resetting P0125 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0125 fault code meaningP0125 repair costhow to fix P0125

Manufacturer & Technical Reference

OBD-II Technical Reference (Engine Cooling & Thermostat)

Related Fault Codes

Auto & OBD-II →
P0125 Fault Code: Insufficient Coolant Temperature… — Fixes & Cost | FaultCodes.org