P0124 Fault Code: Throttle/Pedal Position Sensor/Switch A Circuit Intermittent
OBD-II P0124 (Engine Cooling & Thermostat): Throttle/Pedal Position Sensor/Switch A Circuit Intermittent.
OBD-II fault code P0124 indicates Throttle/Pedal Position Sensor/Switch A Circuit Intermittent. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $43–$486.
- Safe to Operate?
- No — Risk of Damage
- DIY Difficulty
- Moderate (Intermediate)
- System
- Engine Cooling & Thermostat
- Professional Repair
- $43 – $486
What This Fault Code Means
Sensor A is, in practice, throttle position sensor 1 at the throttle body; the accelerator pedal has its own codes (P2120 onwards). With a cable-operated throttle there is a single potentiometer (about 0.5 V closed to 4.5 V wide open). Electronic throttles have two sensors sharing a 5 V reference and ground, usually running in opposite directions – on GM throttle sensor 1 falls from 3–4 V at idle to below 1 V at full throttle. P0124 covers short, recurring dropouts of sensor A. The only manufacturer source naming it is Ford's 2020–2023 summary for digital SENT throttle sensors: an error lasting more than 0.4 s sets P0124, one lasting more than 4 s sets P0120, so brief dropouts are kept apart from lasting faults; MIL and wrench lamp come on. GM does not use P0124 in the tables checked – its low/high monitors already catch intermittent shorts. For analogue sensors the description rests on CARB and component information. Typical causes are loose contacts, a chafed harness or a worn potentiometer track.
Common Symptoms
- Check engine light, possibly only intermittently
- Brief hesitation or power drop
- Limp mode that disappears after restart
- Rough idle
Most Likely Root Causes
- Loose contact in the connector (spread terminals, corrosion)
- Chafed or partly broken wire in the harness
- Worn potentiometer track (dropout at a certain position)
- Sensor electronics faulty (SENT)
Diagnostic Checks Before Replacing Parts
Verify the exact faulty component before ordering replacements.
- 1Read stored freeze-frame data and companion codes alongside P0124.
- 2Inspect electrical connectors, fuses, and harnesses connected to Throttle Position Sensor.
- 3Verify live sensor telemetry before ordering replacement components.
Interactive Symptom Triage
Answer 3 quick checks to narrow down the faulty component before spending money on parts.
Are any companion fault codes stored alongside P0124?
Step-by-Step Troubleshooting & Fix
- 1Scan for companion fault codes and address upstream circuit issues first.
- 2Visually inspect wiring harnesses, plugs, and hoses around Throttle Position Sensor.
- 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
- 4Repair damaged wiring or install an OEM-grade replacement Throttle Position Sensor.
- 5Clear fault memory and run a verification cycle to confirm P0124 does not return.
Estimated Repair Cost Benchmark
Typical DIY parts and certified technician labor ranges. Select a currency below.
| Repair Path | USD |
|---|---|
| DIY Parts Only | $16 – $204 |
| Professional Repair (Parts + Labor) | $43 – $486 |
Frequently Asked Questions
Is it safe to keep operating with fault code P0124?
Avoid prolonged operation until inspected to prevent secondary component damage.
How much does it cost to repair P0124?
DIY replacement parts average $16–$204, while professional service averages $43–$486.
Will resetting P0124 fix the problem permanently?
No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.
Related Searches & Questions
Manufacturer & Technical Reference
OBD-II Technical Reference (Engine Cooling & Thermostat)