P0123 Fault Code: Throttle/Pedal Position Sensor/Switch A Circuit High
OBD-II P0123 (Engine Cooling & Thermostat): Throttle/Pedal Position Sensor/Switch A Circuit High.
OBD-II fault code P0123 indicates Throttle/Pedal Position Sensor/Switch A Circuit High. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $43–$486.
- Safe to Operate?
- No — Risk of Damage
- DIY Difficulty
- Moderate (Intermediate)
- System
- Engine Cooling & Thermostat
- Professional Repair
- $43 – $486
What This Fault Code Means
Sensor A is, in practice, throttle position sensor 1 at the throttle body; the accelerator pedal has its own codes (P2120 onwards). With a cable-operated throttle there is a single potentiometer (about 0.5 V closed to 4.5 V wide open). Electronic throttles have two sensors sharing a 5 V reference and ground, usually running in opposite directions – on GM throttle sensor 1 falls from 3–4 V at idle to below 1 V at full throttle. P0123 means the signal voltage of sensor A is above its upper limit – usually an open sensor ground, which lets the signal float up to the reference, or a signal wire shorted to 5 V or 12 V. Limits: Ford above 4.75 V (within 1 s), Saab/GM 2011 above 4.8 V for 1 s, Saab cable system above 4.96 V for 5 s. Because GM's sensor 1 runs inverted, a high signal there electrically resembles idle, not full throttle. GM sets it after one trip; electronic throttles go into limp mode.
Common Symptoms
- Check engine light, on electronic throttles also wrench lamp
- Limp mode with reduced power ('Reduced Engine Power') on electronic throttles
- Raised idle or delayed throttle response
- Shift problems on automatics
Most Likely Root Causes
- Sensor ground (low reference) open or high-resistance
- Signal wire shorted to 5 V or 12 V
- Sensor or throttle body faulty
- Moisture or corrosion in the connector
Diagnostic Checks Before Replacing Parts
Verify the exact faulty component before ordering replacements.
- 1Read stored freeze-frame data and companion codes alongside P0123.
- 2Inspect electrical connectors, fuses, and harnesses connected to Throttle Position Sensor.
- 3Verify live sensor telemetry before ordering replacement components.
Interactive Symptom Triage
Answer 3 quick checks to narrow down the faulty component before spending money on parts.
Are any companion fault codes stored alongside P0123?
Step-by-Step Troubleshooting & Fix
- 1Scan for companion fault codes and address upstream circuit issues first.
- 2Visually inspect wiring harnesses, plugs, and hoses around Throttle Position Sensor.
- 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
- 4Repair damaged wiring or install an OEM-grade replacement Throttle Position Sensor.
- 5Clear fault memory and run a verification cycle to confirm P0123 does not return.
Estimated Repair Cost Benchmark
Typical DIY parts and certified technician labor ranges. Select a currency below.
| Repair Path | USD |
|---|---|
| DIY Parts Only | $16 – $204 |
| Professional Repair (Parts + Labor) | $43 – $486 |
Frequently Asked Questions
Is it safe to keep operating with fault code P0123?
Avoid prolonged operation until inspected to prevent secondary component damage.
How much does it cost to repair P0123?
DIY replacement parts average $16–$204, while professional service averages $43–$486.
Will resetting P0123 fix the problem permanently?
No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.
Related Searches & Questions
Manufacturer & Technical Reference
OBD-II Technical Reference (Engine Cooling & Thermostat)